Zanussi ZDT12011FA - User Manual

Questions and Answers

J
Jennifer FloresJul 28, 2025
What to do if my Zanussi Dishwasher doesn't fill with water?
- S
  Spencer LopezJul 28, 2025
  If your Zanussi Dishwasher isn't filling with water, several factors could be the cause. First, ensure the water tap is fully open. Also, the water supply pressure might be too low; contact your local water authority for information on water pressure. Check that the water tap and the filter in the inlet hose are not clogged. Finally, inspect the inlet hose to make sure there are no kinks or bends restricting water flow.
S
sonia59Aug 1, 2025
What to do if my Zanussi Dishwasher is not draining water?
- M
  Mr. William WilsonAug 1, 2025
  If your Zanussi Dishwasher isn't draining water, check if the sink spigot is clogged. Also, make sure the drain hose has no kinks or bends that could be obstructing the water flow.
R
Ryan HoldenAug 5, 2025
Why Zanussi ZDT12011FA programme does not start?
- M
  Mr. John HernandezAug 5, 2025
  If the Zanussi Dishwasher programme does not start, ensure the appliance door is fully closed. Also, the appliance may have started the procedure to recharge the resin inside the water softener, which lasts approximately 5 minutes.
S
stevensjosephAug 10, 2025
Why are the dishes still wet in my Zanussi ZDT12011FA Dishwasher?
- B
  Bethany HatfieldAug 10, 2025
  If the dishes are wet after a cycle in your Zanussi Dishwasher, it could be due to several reasons. The selected programme may not have a drying phase or it may have a drying phase with low temperature. Check if the rinse aid dispenser is empty, or if the quality of the rinse aid is not sufficient.
K
Kyle WellsAug 13, 2025
What to do if there are stains and dry water drops on glasses from Zanussi ZDT12011FA?
- S
  Sharon ObrienAug 13, 2025
  If there are stains and dry water drops on glasses and dishes after using your Zanussi Dishwasher, the released quantity of rinse aid may not be sufficient. Try adjusting the rinse aid selector to a higher position. The quality of the rinse aid itself could also be a factor.
J
Joshua HernandezAug 18, 2025
How to remove whitish streaks from Zanussi Dishwasher?
- J
  Jason BlackAug 18, 2025
  If there are whitish streaks or bluish layers on glasses and dishes, the release quantity of rinse aid may be too much. Adjust the rinse aid selector to a lower position. Also, the quantity of detergent used might be excessive.
A
Ashley BarnesAug 22, 2025
What to do if the anti-flood device is on in my Zanussi ZDT12011FA?
- S
  sanchezjeremyAug 22, 2025
  If the anti-flood device is activated in your Zanussi Dishwasher, close the water tap and contact an Authorised Service Centre.

Zanussi ZDT12011FA Specifications

General

Door color	Not applicable
Water fill	Cold
Control type	Buttons
Tub material	Stainless steel
Appliance placement	Fully built-in
Control panel color	Black
Upper basket adjustable height	Yes
Cycle time	195 min
Noise level	51 dB
Dishwashing programs	Eco, Intensive, Quick
Number of place settings	12 place settings
Number of washing programs	5
Number of temperature settings	3
Drying class	A
Annual water consumption	3080 L
Annual energy consumption	290 kWh
Connected load	2200 W
AC input voltage	220 - 240 V
AC input frequency	50 Hz
Power consumption (off)	0.5 W
Water consumption per cycle	14.3 L
Energy consumption per cycle	1.02 kWh

Weight and Dimensions

Depth	555 mm
Width	596 mm
Height	818 mm
Installation compartment depth	570 mm
Installation compartment width	600 mm
Installation compartment height (max)	880 mm
Installation compartment height (min)	820 mm