Zanussi ZDV12002FA User Manual (English)

Other manuals for Zanussi ZDV12002FA

Questions and Answers:

A
Anna RiveraJul 30, 2025
What to do if my Zanussi ZDV12002FA Dishwasher doesn't fill with water?
- C
  Cheryl MarquezJul 31, 2025
  If your Zanussi Dishwasher isn't filling with water, several factors could be the cause. First, ensure the water tap is fully open. Also, the water supply pressure might be too low; contact your local water authority for information on water pressure. Check that the water tap and the filter in the inlet hose are not clogged. Finally, inspect the inlet hose to make sure there are no kinks or bends restricting water flow.
A
allen80Aug 3, 2025
What to do if my Zanussi ZDV12002FA Dishwasher is not draining water?
- T
  tschmittAug 3, 2025
  If your Zanussi Dishwasher isn't draining water, check if the sink spigot is clogged. Also, make sure the drain hose has no kinks or bends that could be obstructing the water flow.
J
Joseph PearsonAug 7, 2025
Why Zanussi ZDV12002FA Dishwasher programme does not start?
- S
  sheilanguyenAug 8, 2025
  If the Zanussi Dishwasher programme does not start, ensure the appliance door is fully closed. Also, the appliance may have started the procedure to recharge the resin inside the water softener, which lasts approximately 5 minutes.
J
Jerry ZamoraAug 12, 2025
Why are the dishes still wet in my Zanussi ZDV12002FA Dishwasher?
- Q
  qmontesAug 12, 2025
  If the dishes are wet after a cycle in your Zanussi Dishwasher, it could be due to several reasons. The selected programme may not have a drying phase or it may have a drying phase with low temperature. Check if the rinse aid dispenser is empty, or if the quality of the rinse aid is not sufficient.
R
rwatsonAug 16, 2025
What to do if there are stains and dry water drops on glasses from Zanussi ZDV12002FA?
- C
  Carly RosarioAug 16, 2025
  If there are stains and dry water drops on glasses and dishes after using your Zanussi Dishwasher, the released quantity of rinse aid may not be sufficient. Try adjusting the rinse aid selector to a higher position. The quality of the rinse aid itself could also be a factor.
M
Ms. Angela WrightAug 21, 2025
How to remove whitish streaks from Zanussi Dishwasher?
- W
  Wesley ReedAug 21, 2025
  If there are whitish streaks or bluish layers on glasses and dishes, the release quantity of rinse aid may be too much. Adjust the rinse aid selector to a lower position. Also, the quantity of detergent used might be excessive.
J
John MyersAug 26, 2025
What to do if the anti-flood device is on in my Zanussi Dishwasher?
- S
  Samantha ArroyoAug 26, 2025
  If the anti-flood device is activated in your Zanussi Dishwasher, close the water tap and contact an Authorised Service Centre.

Zanussi ZDV12002FA Specifications

General

Door color	Not applicable
Control type	Buttons
Built-in display	No
Appliance placement	Fully built-in
Control panel color	Black
Upper basket adjustable height	Yes
Noise level	53 dB
Delayed start timer	-
Dishwashing programs	Eco, Intensive, Normal, Quick
Number of place settings	9 place settings
Number of washing programs	5
Number of temperature settings	3
Drying class	A
Annual water consumption	2660 L
Annual energy consumption	250 kWh
Connected load	220 W
AC input voltage	220 - 240 V
AC input frequency	50 Hz
Water consumption per cycle	9.5 L
Energy consumption per cycle	- kWh