Zanussi ZDV14003FA User Manual (English)

Questions and Answers:

E
Elizabeth OwensAug 16, 2025
Why is my Zanussi Dishwasher not filling with water?
- S
  Steven MortonAug 16, 2025
  If your Zanussi Dishwasher isn't filling with water, there could be several reasons. First, ensure the water tap is fully open. If the end indicator flashes once and you hear an acoustic signal once intermittently, this likely the issue. Also, the pressure of the water supply might be too low, so contact your local water authority to check. Other potential causes include a clogged water tap or a clogged filter in the inlet hose. Finally, make sure the inlet hose isn't kinked or bent.
B
Brittany DavisAug 19, 2025
What to do if my Zanussi ZDV14003FA Dishwasher does not drain the water?
- C
  Chad MarksAug 19, 2025
  If your Zanussi Dishwasher isn't draining water, the sink spigot may be clogged, especially if the end indicator flashes twice intermittently and you hear two acoustic signals intermittently. Also, make sure the drain hose isn't kinked or bent.
C
chrisjonesAug 22, 2025
Why is my Zanussi Dishwasher leaking from the door?
- L
  lisa81Aug 22, 2025
  If there's a small leak from the door of your Zanussi Dishwasher, the appliance may not be levelled correctly. Try loosening or tightening the adjustable feet. If that doesn't work, the door may not be centred on the tub; adjust the rear foot if possible.
B
bradley70Aug 25, 2025
Why does the Zanussi ZDV14003FA program last too long?
- M
  Melvin FoxAug 26, 2025
  If a program on your Zanussi Dishwasher is running longer than expected, check if the delayed start option is enabled. If it is, either cancel the delay setting or wait for the countdown to complete.
M
Michelle GlassAug 28, 2025
Why does my Zanussi ZDV14003FA Dishwasher keep tripping the circuit breaker?
- D
  dwaltonAug 28, 2025
  If your Zanussi Dishwasher is tripping the circuit-breaker, it could be due to a couple of reasons. It's possible the amperage is insufficient to supply all appliances in use simultaneously. Check the socket amperage and the capacity of the meter, or turn off another appliance. Alternatively, there could be an internal electrical fault with the dishwasher, in which case you should contact an Authorised Service Centre.
T
Tiffany WallsAug 30, 2025
What to do if Zanussi ZDV14003FA programme does not start?
- K
  Kristina FloresAug 31, 2025
  If the program on your Zanussi Dishwasher isn't starting, ensure that the appliance door is properly closed. Also, if the delay start function is activated, either cancel the setting or wait for the countdown to finish. It's also possible that the appliance has started a procedure to re-charge the resin inside the water softener, which can take approximately 5 minutes.
J
joshua09Sep 3, 2025
How to fix rattling sounds in Zanussi ZDV14003FA?
- M
  Mary MilesSep 3, 2025
  If you hear rattling or knocking sounds from inside your Zanussi Dishwasher, it's likely that the tableware is not properly arranged in the baskets. Make sure to refer to the basket loading leaflet for guidance. Also, ensure that the spray arms can rotate freely without obstruction.
L
Lisa HallSep 6, 2025
Why is the Zanussi ZDV14003FA door difficult to close?
- B
  brownannaSep 6, 2025
  If the door of your Zanussi Dishwasher is difficult to close, it could be that the appliance isn't levelled properly; try loosening or tightening the adjustable feet. Also, check if any parts of the tableware are protruding from the baskets, obstructing the door.
M
Marcia AllenSep 8, 2025
What to do if the anti-flood device is on in Zanussi ZDV14003FA?
- J
  Jonathan StoneSep 9, 2025
  If the anti-flood device on your Zanussi Dishwasher is activated (the end indicator flashes three times intermittently and you hear three acoustic signals intermittently), close the water tap and contact an Authorised Service Centre.
D
dcraigSep 12, 2025
Why does Zanussi ZDV14003FA stop and start during operation?
- G
  Geoffrey ThomasSep 12, 2025
  It is normal for the Zanussi Dishwasher to stop and start multiple times during operation. This behavior helps achieve optimal cleaning results and saves energy.