What to do if my Zanussi ZNI814PDWV Washer does not drain water?
If your Zanussi Washer isn't draining water, first, check if the sink spigot is clogged. Then, ensure the drain hose isn't kinked or bent. Clean the drain filter if it's clogged. Make sure the drain hose is correctly connected. Finally, if you selected a program without a drain phase or an option that leaves water in the tub, set the drain program.
Why is the spin cycle not working on my Zanussi ZNI814PDWV, or why does the washing cycle last longer than usual?
If the spin phase of your Zanussi Washer isn't working or the wash cycle is taking longer than normal, try setting the spin program. Check if the drain filter is clogged and clean it if necessary. Manually adjust the items in the tub to balance the load, and then restart the spin phase.
What to do if I cannot open the door of my Zanussi Washer?
If you can't open the door of your Zanussi Washer, make sure a program that ends with water in the tub hasn't been selected and that the washing program has finished. If there's water in the drum, set the drain or spin program. Ensure the appliance is receiving electrical power. If the problem persists, it may be due to an appliance failure. Contact the Authorised Service Centre. Refer to "Emergency door opening" for instructions.
Why is my Zanussi Washer not filling with water properly?
If your Zanussi Washer isn't filling with water correctly, ensure the water tap is fully open and that the water supply pressure isn't too low. Check that the water tap isn't clogged and that the inlet hose has no kinks, damages, or bends. Verify the water inlet hose connection is correct and that the filter of the inlet hose and the filter of the valve are not clogged. For information about water pressure, contact your local water authority. Refer to 'Care and cleaning' to learn about filter cleaning.
Why does my Zanussi ZNI814PDWV Washer fill with water and drain immediately?
If your Zanussi Washer fills with water and then drains immediately, make sure that the drain hose is in the correct position. The hose may be positioned too low. Refer to "Installation instruction".
What to do if the door of my Zanussi Washer is open or not closed correctly?
Make sure that the door of your Zanussi Washer is properly closed.
How to fix a Zanussi ZNI814PDWV Washer that makes unusual noise and vibrates?
If your Zanussi Washer is making unusual noises and vibrating, ensure it is correctly leveled. Also, confirm that all packaging and transit bolts have been removed. If the load is too small, add more laundry to the drum.
Why are the washing results not satisfactory with my Zanussi Washer?
If the washing results from your Zanussi Washer are not satisfactory, increase the amount of detergent or switch to a different detergent. For stubborn stains, pretreat the laundry with special stain removal products. Ensure you're setting the correct temperature and avoid overloading the machine.
How to reduce foam in my Zanussi ZNI814PDWV Washer during the washing cycle?
If there is too much foam in the drum of your Zanussi Washer during the wash cycle, reduce the amount of detergent you're using, or decrease the number of detergent tablets or single-dose detergents.
Why does the program duration change during the Zanussi ZNI814PDWV cycle?
The AutoAjust System in your Zanussi Washer adjusts the program duration based on the type and size of the laundry load. Refer to "The AutoAjust System load detection" in "Daily Use" chapter.
General| Model | ZNI814PDWV |
|---|---|
| Type | Freestanding |
| Appliance placement | Freestanding |
| Color | White |
| Built-in display | Yes |
| Drum material | Stainless steel |
| Rated capacity | 8 kg |
| Maximum spin speed | 1400 RPM |
| Spin-drying class | B |
| Washing class | A |
| Number of washing programs | 14 |
| Delayed start timer | Yes |
| Noise level (spinning) | 75 dB |
| Loading type | Front load |
| Width | 597 mm |
| Height | 85 cm |
| Depth | 59 cm |
To Next Page
