What to do if my Zanussi ZWF142F1G2 Washer does not drain the water?
If your Zanussi Washer isn't draining, check a few things: * Ensure the sink spigot isn't clogged. * Make sure the drain hose has no kinks or bends. * Verify the drain hose connection is correct. * If you set a programme without a drain phase, set the drain programme. * Set the drain programme if you set an option which ends with water in the tub.
Why won't my Zanussi ZWF142F1G2 programme start?
If your Zanussi Washer programme won't start, consider these potential solutions: * Ensure the mains plug is connected to the mains socket. * Make sure the appliance door is closed. * Check for any damaged fuses in the fuse box. * Ensure that the Inicio/Pausa button has been touched. * If a delay start is set, cancel the setting or wait for the countdown to finish. * Deactivate the Child Lock function if it's active. * Check the position of the knob on the selected programme.
What to do if I cannot open the Zanussi ZWF142F1G2 door?
If you cannot open the door of your Zanussi Washer, consider the following: * Ensure a washing programme that ends with water in the tub hasn't been selected. * Make sure the washing programme has finished. * If there's water in the drum, set the drain or spin programme. * Ensure the appliance is receiving electrical power.
Why does the Zanussi Washer spin phase not operate or the washing cycle lasts longer than usual?
If the spin phase of your Zanussi Washer isn't working or the cycle is longer than usual: * Set the spin programme. * Try manually adjusting the items in the tub and starting the spin phase again, as balance problems may be the cause.
What to do if my Zanussi Washer fills with water and drains immediately?
If your Zanussi Washer fills with water and drains immediately, ensure the drain hose is in the correct position. The hose may be positioned too low. Refer to "Installation instruction".
What to do if the Zanussi ZWF142F1G2 appliance door is open or not closed correctly?
Make sure that the door of your Zanussi Washer is properly closed.
What to do if my Zanussi ZWF142F1G2 Washer does not fill with water properly?
If your Zanussi Washer isn't filling with water, check the following: * Ensure the water tap is open. * Check that the water supply pressure isn't too low (contact your local water authority for information). * Make sure the water tap isn't clogged. * Ensure the inlet hose has no kinks, damages, or bends. * Verify the water inlet hose connection is correct. * Make sure that the filter of the inlet hose and the filter of the valve are not clogged. Refer to 'Care and cleaning'.
What to do if there is water on the floor near my Zanussi ZWF142F1G2?
If you find water on the floor near your Zanussi Washer, take these steps: * Ensure the water hose couplings are tight and there are no water leakages. * Check the water inlet and drain hoses for any damages. * Make sure you're using the correct detergent and the appropriate amount.
Why is my Zanussi Washer making unusual noises and vibrating?
If your Zanussi Washer is making unusual noises and vibrating, check these: * Make sure the appliance is correctly leveled. Refer to "Installation instruction". * Ensure that the packaging and/or transit bolts have been removed. Refer to "Installation instruction". * Try adding more laundry to the drum, as the load might be too small.
Why are the washing results from my Zanussi ZWF142F1G2 not satisfactory?
If you're not happy with the washing results from your Zanussi Washer: * Increase the detergent quantity or switch to a different detergent. * Use special products to pre-treat stubborn stains before washing. * Ensure you're setting the correct temperature. * Decrease the laundry load.
General| Spin Speed | 1400 rpm |
|---|---|
| Energy Efficiency Class | A+++ |
| Color | White |
| Noise Level (Spinning) | 78 dB |
| Loading type | Front-loading |
To Next Page
