To Next PageTo Next PageWhat to do if my Zenith Water Filtration System has a water leak?
If you notice a water leak, immediately turn off the mains water supply to prevent further leakage. After that call for service.
How to fix condenser screen blocked in Zenith Water Filtration Systems?
If the condenser screen is blocked, it is likely due to a blocked air filter. Remove the blockage, clean the filter, and check the user guide for detailed instructions.
What to do if my Zenith Water Filtration System shows condenser overtemp.?
If your Zenith Water Filtration System shows a condenser overtemp message, this is likely due to a blocked air filter. Remove the blockage, clean the filter, and consult the user guide for further assistance.
Why Zenith Water Filtration System compressor over-run?
A compressor over-run in your Zenith Water Filtration System is caused by the compressor being too hot. Ensure that the ventilation is adequate to cool the compressor.
What to do for boil dry protection in Zenith Water Filtration Systems?
If the boil dry protection is activated on your Zenith Water Filtration System, turn the power OFF and then ON to reset the system.
What causes hot tank under filled in Zenith Water Filtration Systems?
A hot tank that is under filled is caused by low water pressure. Check the water supply to ensure adequate pressure.
What to do if Zenith Water Filtration System has a power board fault?
If there is a power board fault, check the power supply and all fuses.
What to do if I see a water leak in my Zenith Water System?
If you observe a water leak in your Zenith Water System, immediately turn off the main water supply. It is also recommended to call for service.
Why has the water supply failed in my Zenith Water System?
If the water supply to your Zenith Water System has failed, first check that the water supply is turned ON.
How to fix a blocked condenser screen on my Zenith Water System?
If the condenser screen is blocked on your Zenith Water System, it is likely due to a blocked air filter. Remove the blockage, clean the filter, and check the user guide for further assistance.
General| Brand | Zenith |
|---|---|
| Model | HydroTap G4 |
| Category | Water Filtration Systems |
| Language | English |
Explains the safety lock feature to prevent boiling water flow.
Details touch sensitive controls for dispensing Boiling, Chilled and Sparkling water.
Explains operation of levers for dispensing and mixer tap function.
Describes operation of select button and rotary control for dispensing water.
Explains handle operation for flow rate and temperature control.
Instructions for dispensing chilled water on Classic, Elite, and Arc/Cube taps.
Instructions for dispensing boiling water with safety feature disabled.
Instructions for dispensing boiling water with safety feature enabled.
Instructions for dispensing sparkling water on Classic, Elite, and Arc/Cube taps.
Explains the meaning of Red Boiling and Blue Chilled water indicator lights.
Details the flashing warning light indicating system faults.
Describes filter light status for different tap models.
Step-by-step guide for calibrating the safety sensor on lever models.
Introduces the TOUCH screen for easy setup and operation adjustment.
Details the main menu, sub-menu, and sub-menu options with section references.
Instructions on how to change the language setting via the LCD menu.
How to view product info, system faults, and filter logs.
Guide to filter flush and filter reset procedures via the LCD.
Instructions for boiling calibration and booster unit configuration.
Procedures for purging CO2 gas lines and calibrating the Lux sensor.
How to set or change a password to protect system settings.
Information on using Wifi for remote monitoring and control.
How to set date/time and adjust boiling/chilled temperatures.
Instructions to adjust filter life and edit filter usage.
Details on Sleep mode and ON/OFF mode for energy saving.
How to schedule ON/OFF times for different days or groups.
Instructions for setting tap safety and activating Hot Isolation.
How to change the maximum dispensing time for hot, chilled, and sparkling water.
Explains how the unit notifies when filter replacement is due.
Step-by-step instructions for changing the water filter cartridge.
Cautions regarding water spillage, O-ring contact, and cartridge insertion.
Instructions for cleaning and maintaining the air inlet filter.
Procedure for changing the 2.6kg CO2 gas bottle for sparkling water.
Explains icons indicating the safety switch status (LOCKED/UNLOCKED).
Details the icon indicating when sleep mode is active.
Explains the icon that shows the heater is in OFF mode.
Describes the icon displaying remaining filter life.
Explains icons for Boiling and Chilled water temperatures.
Provides Zenith Heaters Limited's head office address, phone, and website.
Lists registered trademarks and patent information for Zenith products.
