EasyManua.ls Logo

Zoeller 1910-0009 - User Manual

Zoeller 1910-0009
12 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
1
Español p. 13
PRE-PLUMBED
SEWAGE SYSTEM
MODEL #1910-0009
Serial Number
Purchase Date
Zoeller
®
is a registered trademark
of Zoeller Co. All Rights Reserved.
Questions, problems, missing parts? Before returning to your retailer, call our customer
service department at 1-800-584-8089, 7:30 a.m. - 5:00 p.m., EST, Monday - Friday.
ATTACH YOUR RECEIPT HERE
025186 B

Table of Contents

Questions and Answers

  • M
    Margaret DawsonAug 3, 2025
    How to troubleshoot a Zoeller 1910-0009 pump that will not start?
    • J
      Jaclyn ElliottAug 3, 2025
      If your Zoeller Plumbing Product pump isn't starting, several factors could be at play. First, ensure the water level is high enough to activate the switch. Check for a blown fuse or tripped circuit breaker; if found, identify the cause before replacing the fuse or resetting the breaker. A clogged inlet screen can also prevent the pump from starting, so remove any debris. Similarly, obstructions to the switch's movement should be cleared. If the issue persists, low line voltage might be the cause, requiring an electrician's expertise. In more severe cases, the motor or switch itself may be defective, necessitating replacement of the pump or switch.
  • K
    kimberlywadeAug 8, 2025
    Why does my Zoeller 1910-0009 pump start and stop too often?
    • S
      schroedergaryAug 8, 2025
      If your Zoeller Plumbing Product pump is starting and stopping frequently, the following might be the reasons. Water could be flowing back into the basin from the discharge pipe; installing a check valve can resolve this. A defective switch may also cause this issue, requiring replacement. Additionally, the check valve itself might not be functioning correctly or could be leaking. Ensure the check valve is properly installed and operating; if necessary, replace it.
  • T
    Toni HornAug 13, 2025
    What to do if Zoeller 1910-0009 Plumbing Product pump operates, but delivers little or no water?
    • D
      Debra HillAug 13, 2025
      If your Zoeller Plumbing Product pump is running but not delivering water, several issues could be responsible. Check for low line voltage, which requires an electrician. A clogged inlet screen can also restrict water flow; remove any obstructions. Inspect the impeller for damage or debris, cleaning or replacing it as needed. Ensure the check valve is not stuck closed or installed backward; correct its installation or replace it if necessary. Also, verify that the shut-off valve is open.
  • M
    Michael PhelpsAug 19, 2025
    Why does my Zoeller 1910-0009 pump shut off and turn on by itself?
    • P
      Phillip RobertsAug 19, 2025
      If your Zoeller Plumbing Product pump is turning off and on independently of the switch, tripping the thermal overload protection, several factors could be involved. Excessive water temperature may be the cause; the pump should not be used for water above 104°F (40°C). A defective or obstructed switch can also lead to this issue; replace the switch or remove any obstructions. A clogged discharge pipe could be the reason; remove the clog. Low line voltage can also cause this, requiring an electrician.
  • C
    castrokaylaAug 23, 2025
    How to reduce noise and vibration in a Zoeller 1910-0009 pump?
    • T
      Thomas NelsonAug 23, 2025
      Excessive noise or vibration in your Zoeller Plumbing Product pump can stem from several sources. Worn bearings may be the culprit, necessitating pump replacement. The impeller might be clogged or damaged; if applicable, remove the screen and volute to clean or replace the impeller. Rigid or loose piping attachments to the building structure can also transmit vibrations; install a rubber coupling to isolate the pump's vibration from the discharge piping.
  • M
    Morgan ReevesAug 28, 2025
    What causes a Zoeller Plumbing Product pump to run continuously?
    • I
      isaac11Aug 28, 2025
      If your Zoeller Plumbing Product pump won't shut off, several issues could be the cause. A defective or obstructed switch can prevent proper operation; replace the switch or remove any obstructions. A clogged discharge pipe can also keep the pump running; clear the clog. If the water inflow exceeds the pump's capacity, re-check the sizing calculations to ensure you have the correct pump size.

Summary

Safety Information

Electrical Shock Safety

Details critical DANGER and WARNINGs regarding electrical shock hazards during installation and operation.

Other Safety Precautions

Includes warnings about swimming pool use, chemical exposure, and California Proposition 65.

Cautions and Preparation

Product Damage Warnings

Highlights potential for product damage due to incorrect power source or operating temperature.

Package Contents and Tools

Lists included components, estimated installation time, and required tools/parts.

General Pump Information

Pump Operation and Levels

Explains sewage pump function, float switch operation, and specific on/off water levels.

Installation Instructions

Site Preparation

Guides on excavating, preparing the base material, and placing the basin levelly.

System Assembly

Details connecting inlet piping, backfilling, securing the power cord, and assembling discharge/vent pipes.

Care and Maintenance

Routine Inspections

Provides instructions for inspecting and testing the system every three months, focusing on float switch cleanliness.

Troubleshooting

Common Issues and Solutions

Addresses problems like pump not starting, stopping too often, or operating noisily with corrective actions.

Performance Problems

Details solutions for pumps delivering little or no water, including voltage, clogs, and check valve issues.

Warranty and Parts

Replacement Parts

Lists available replacement parts and provides a customer service number for ordering.

Product Warranty Details

Outlines the warranty period, conditions, limitations, and procedures for service claims.

Zoeller 1910-0009 Specifications

General IconGeneral
Model Number1910-0009
Discharge Size1-1/2" NPT
Motor Housing MaterialCast Iron
Cord Length10 ft
Solids Handling2"
PhaseSingle-Phase

Related product manuals