Thank you for choosing ZOMM.
If you have any questions, please contact our support team at support.zomm.com.
BLUETOOTH® IS A TRADEMARK OWNED BY THE BLUETOOTH SIG, INC. AND IS USED UNDER LICENSE
ZOMM® IS A TRADEMARK OF ZOMM, LLC WIRELESS LEASH™ IS A TRADEMARK OF ZOMM, LLC
myZOMM™ IS A TRADEMARK OF ZOMM, LLC
© ZOMM, LLC 2010, 2011 ALL RIGHTS RESERVED
MATERIAL PRESENTED WITHIN SUBJECT TO CHANGE WITHOUT NOTICE
in the box
about the ZOMM Wireless Leash
Z-button (with Z-light)
perimeter alert light
micro-USB port with dust cover
metal loop
reset but ton
high-powered micro-speaker
noise-cancelling microphone
charging the ZOMM
NOTE: If the ZOMM is on and connected to your phone, all of its features
will function while charging.
1. Gently open the dust cover.
2. Insert the micro-USB end of the charging cable into the
ZOMM’s m ic r o- U S B p or t .
Low Battery Alert: When the battery level is low, the ZOMM will alert you by
sounding three short beeps every few minutes.
When charging, the ZSPNO[^PSSÅHZOVUJLWLYZLJVUK HUK^OLUJOHYNLK^PSS
remain li t. For best b attery life, f ully charge th e ZOMM for 4 hours.
USB Wall Charger:
3. Insert the USB cable into the wall charger and
then plug the wall charger into a wall outlet.
Computer:
3. Insert the cable into one of your computer’s USB
ports. Make sure your computer is on and awake
for the duration of the charge.
Car Charger:
3. Insert the USB cable into the car charger and then
insert the car charger into your car’s power port
or cigarette lighter.
1. Navigate to zomm.com.
2. Click on the myZOMM link at the top of the page.
3. Log in or create an account.
4. Follow the instructions to update or customize your ZOMM.
Be sure to customize your ZOMM with myZOMM to get
all the latest features and updates!
customizing the ZOMM
off
1. Ensure your phone is turned ON and the
Bluetooth
feature is enabled.
2. Veri fy t hat the ZOMM is unplugged and turned OFF
(Z-light is OFF).
3. Press and hold the Z-button until you hear the second beep
(9 seconds).
4. On your phone, search for
Bluetooth
devices.
5. Select the ZOMM from the list of found
Bluetooth
devices
on your phone.
6. Pair and connect the ZOMM. If a PIN is required, use 0000.
hold until
2nd beep
56;,!6UJLJVUULJ[LK[OLASPNO[^PSSÅHZO
every few seconds.
pairing the ZOMM
off
connect
to
ZOMM?
0000
quick start guide
visit zomm.com to customize and receive
updates for your ZOMM
®
Wor ld’s Fir st W irel ess Lea sh
™
for Mobile Phones
one ZOMM
Wireless Leash
one quick-release
keychain
one visor clip
one micro-USB
charging cable
one USB
wall charger
one car charger
Keychain (closed)
Keychain (open)
insert keyring in
open slot
Insert into visor clip
as shown
Pull the metal loop
downwards to remove
1. Attach the ZOMM to one of the four quick-release key rings.
2. Pull the quick-release slide toward the center of the key-ring
hub to remove or re-attach any of the key rings.
3. The quick-release slide will spring back into the locked
position when you let go of it.
1. Slide the clip onto the right-hand side of your visor with the
ZOMM holder facing down.
2. Snap the ZOMM into the visor clip with the Z-button facing
down and the metal loop toward the windshield.
3. To r em o ve t he ZOMM from the clip, pull the metal loop
downwards.
using the quick-release keychain
using the visor clip
To Next Page
General