Why when starting the Zoomlion Excavators, the starter motor doesn’t work?
If the starter motor doesn't work when starting your Zoomlion Excavators, check and repair the wire if there is fault. Change the starter motor if it has fault. Charge the battery if the battery storage is undercharged.
Why is the hydraulic oil too hot in my Zoomlion Excavators?
If the hydraulic oil in your Zoomlion Excavators is overheating, the filter might be blocked, so install a new filter. Another potential cause is blocked radiator or oil cooler. In this case, clean and straighten the blade.
What to do if my Zoomlion ZE205E engine oil pressure indicator light is on?
If the engine oil pressure indicator light is illuminated on your Zoomlion Excavators, several factors could be responsible. Start by checking the engine oil filter; if it's blocked, replace it. Additionally, inspect the oil pipe and joints for looseness or damage that may be causing leaks and repair if needed. Also, the engine oil pressure sensor could be faulty and require replacement, or the indicator itself may be faulty, requiring replacement.
What to do if the hydraulic pressure functions slowly in Zoomlion ZE205E Excavators?
If the hydraulic pressure in your Zoomlion Excavators is functioning slowly, it could be due to several reasons. First, check the oil level and refill the oil collector to the full scale if it is low. Also, if the oil is cold, preheat the machine. If the engine speed is too low, increase the speed.
Why is the vapor squirting from the top of the radiator (the pressure valve) in my Zoomlion ZE205E Excavators?
If vapor is squirting from the top of the radiator (pressure valve) in your Zoomlion Excavators, it could be due to a low coolant level or a water leak. Check the coolant level, add water if necessary, and repair any leaks. Also, a loose fan belt can cause overheating, so check the tension of the fan belt and adjust or replace it. Another potential cause is accumulation of dirty things or lime scale in the cooling system, so change the cooling liquid and wash the interior of the cooling system.
What to do if the hydraulic cylinder works but can’t hoist the load on my Zoomlion ZE205E?
If the hydraulic cylinder on your Zoomlion Excavators works but cannot hoist the load, ensure that the hydraulic oil level is sufficient by adding oil. Also, check the suction filter for blockages and clean the filter and the system. Finally, check the suction pipeline of the pump for leaks.
What to do if air bleeding sound can be heard occasionally in the burning noise of Zoomlion ZE205E?
If you occasionally hear an air bleeding sound within the burning noise of your Zoomlion Excavators, the injection nozzle may be faulty, so change the injection nozzle.
What to do if the pinion of the starter motor sometimes works but sometimes doesn’t work in Zoomlion ZE205E?
If the pinion of the starter motor on your Zoomlion Excavators sometimes works and sometimes doesn’t, charge the battery if the battery storage is undercharged. Change the safety relay if it has fault.
What to do if a hydraulic cylinder doesn’t work in Zoomlion Excavators?
If a hydraulic cylinder isn’t working on your Zoomlion Excavators, repair or change the hydraulic pipeline if it is damaged. Fasten the joint if it is loose. Install a new O-ring if the O-ring in the joint is damaged.
What to do if the oil foams in Zoomlion ZE205E Excavators?
If the oil in your Zoomlion Excavators is foaming, check the oil pipeline for twists or pits. Also, if there is water in the oil, change the oil. Finally, if the oil level is high or low, adjust the oil level.
General| Maximum Digging Force (Bucket) | 138 kN |
|---|---|
| Gradeability | 35° |
| Operating Weight | 20500 kg |
| Bucket Capacity | 0.8 - 1.0 m³ |
| Max Digging Depth | 6, 620 mm |
| Max Dumping Height | 6, 700 mm |
| Travel Speed | 5.5 km/h |
To Next Page
