Positioning the WAP6807
Set up using the WPS button
WAP6807
Gigabit Wireless Extender
Quick Start Guide
Package Contents
Power AdapterDevice Ethernet Cable Quick Start
Guide
DoC
Declaration of
Conformity
Safety Warnings
1/1
within
2 minutes
Bottom view
3
1
3
2
2
1
2
3
4
POWER ON/OFF
LAN1 LAN2
RESET
POWER ON
Rear Panel
Wait until the power LED
turns steady green
Router
WPS
WAP6807
WPS
Need WiFi here
Room 1 Room 2
Router WAP6807 Clients
WAP6807
Router
Device
Label
SSID: DH_XXXXXX
Wireless key: XXXXXXXXXX
WiFi
DH_XXXXXX
Connect
4
If you need any assistance please call us on 0333 0155156 or
email help@digitalhomeuk.com
www.digitalhomeuk.com
1
Press the WPS button on the Zyxel MPro Mesh Router. Release it when the Zyxel MPro Mesh
Router WPS LED blinks.
Press the WPS button on the WAP6807 once and release it. The POWER and LINK
LEDs blink amber indicate the pairing is in process.
The WAP6807 LINK and POWER LEDs light up green if the connection is successful.
On your smartphone or wireless client, find the Zyxel MPro Mesh Router SSID. Enter the
Zyxel MPro Mesh Router wireless key to connect.
Note: The POWER LED on the WAP6807 indicates if the WAP6807 is ready to join the
WiFi network. The LINK LED on the WAP6807 indicates WiFi link quality and WPS pairing
status. See the LED table.
Gre
en On
- Good WiFi connection to the router.
Amber
Red
On - Signal is too strong.
Move the WAP6807 away from the router.
Blinking - Connecting to the router. Please wait.
On -
Signal is too weak. Move the WAP6807 closer to the router
Off - No connection.
Link
Green
Amber
Red
On - Device ready in Repeater mode.
Blinking - Device booting. Please wait.
On - Device ready in AP mode.
Blinking - Device joining WiFi network. Please wait.
On - Device failed to join the WiFi network.
Off - Device is not receiving power.
Power
Positioning the WAP6807
1. Place the WAP6807 between your router and where you want to extend your
wireless network.
Note: The WAP6807 requires a good wireless connection back to the main router as
indicated by a green LINK status LED. See set up below.
Powering up the WAP6807
2. Rotate the stand on the bottom of the WAP6807 90 degrees.
3. Plug in the power adapter and turn on the WAP6807.
Wait for about 2 minutes. The Power
LED lights up steady green.
POWER ON/OFF
LAN1 LAN2
RESET
Router
LAN
LAN
WAP6807
Use the second ethernet cable provided to connect one of the yellow LAN ports on the
main router to one of the yellow LAN ports on the WAP 6807.
Power on the WAP 6807. This will automatically pair the extender with the main router
and download the correct MPro Mesh configuration.
During the set up the POWER and LINK LEDs blink amber to indicate the pairing is in
process.
The WAP6807 LINK and POWER LEDs light up solid green if the connection is
successful.
The WAP 6807 can now be unplugged (from the power and ethernet cables) and moved
to a location where the extended WiFi signal is required (connecting the power cable at
the required location).
Note: The WAP 6807 requires a good wireless connection back to the main router as
indicated by a green LINK status LED. If there is no LINK light then the WAP 6807 needs
to be moved closer to the main router.
Set up using the Ethernet cable - Recommended
To Next Page
Need help?
General
