Need help?Do you have a question about the ZyXEL Communications XGS1930-52 and is the answer not in the manual?
General| Switch type | Managed |
|---|---|
| Switch layer | L3 |
| Quality of Service (QoS) support | Yes |
| SFP+ module slots quantity | 4 |
| Installed SFP modules quantity | - |
| Basic switching RJ-45 Ethernet ports type | Gigabit Ethernet (10/100/1000) |
| Basic switching RJ-45 Ethernet ports quantity | 48 |
| Number of VLANs | 4000 |
| Routing entries | 32 |
| Networking standards | IEEE 802.1D, IEEE 802.1Q, IEEE 802.1ab, IEEE 802.1p, IEEE 802.1s, IEEE 802.1w, IEEE 802.1x, IEEE 802.3, IEEE 802.3ab, IEEE 802.3u, IEEE 802.3x, IEEE 802.3z |
| Virtual LAN features | Port-based VLAN, Voice VLAN |
| Copper ethernet cabling technology | 10BASE-T, 100BASE-TX, 1000BASE-T |
| Forwarding rate | 130.9 Mpps |
| MAC address table | 16000 entries |
| Packet buffer memory | 1.5 MB |
| DHCP features | DHCP client, DHCP relay, DHCPv6 relay |
| Authentication | Guest VLAN, MAC-based authentication, Port-based authentication |
| Security algorithms | 802.1x RADIUS, SHA-2, SNMPv3, SSL/TLS |
| Package type | Box |
| Package depth | 355 mm |
| Package width | 616 mm |
| Package height | 107 mm |
| Package weight | 4780 g |
| Cables included | AC |
| Heat dissipation | 189.937 BTU/h |
| Storage temperature (T-T) | -40 - 70 °C |
| Operating temperature (T-T) | 0 - 50 °C |
| Operating relative humidity (H-H) | 10 - 95 % |
| AC input voltage | 100 - 240 V |
| AC input frequency | 50 - 60 Hz |
| Power consumption (max) | 55.7 W |
| Noise level | 26.3 dB |
| Flash memory | 32 MB |
| Internal memory | 512 MB |
| Mean time between failures (MTBF) | 827093 h |
| Product color | Black |
| Electromagnetic compatibility | FCC 15 A, CE A, BSMI EMC |
| Harmonized System (HS) code | 85176990 |
Weight and Dimensions| Depth | 270 mm |
|---|---|
| Width | 441 mm |
| Height | 44 mm |
| Weight | 3700 g |
This chapter introduces the main features and applications of the Switch, including its models and management modes.
This chapter details how to install and connect the Switch, covering installation scenarios, safety precautions, and mounting procedures.
This chapter explains the configuration and functions of the Web Configurator for system setup and management.
This chapter demonstrates how to set up the Switch for an example network, covering VLAN creation and IP configuration.
This chapter details how to configure System Info, General Setup, Switch Setup, IP Setup, Port Setup, PoE Setup, and IPv6.
This chapter explains how to configure 802.1Q tagged and port-based VLANs, including VLAN status and configuration.
This chapter covers Spanning Tree Protocol (STP), Rapid Spanning Tree Protocol (RSTP), and Multiple Spanning Tree Protocol (MSTP).
This chapter describes IEEE 802.1x, MAC, and Guest VLAN authentication methods for port access control.
This chapter shows how to set up port security, allowing only authorized MAC addresses to pass through a port.
This chapter describes how to configure authentication, authorization, and accounting settings on the Switch.
This chapter explains how DHCP snooping works to build a binding table and filter unauthorized DHCP packets.
This chapter explains how to configure rate limits, actions for errors, and error-disable recovery.
This chapter shows how to configure the DHCP feature, including DHCPv4 and DHCPv6 relay.
This chapter explains how to maintain firmware and configuration files, including backup and restore procedures.
This chapter describes how to control access to the Switch, covering SNMP, logins, and remote management.
This chapter offers suggestions to solve problems encountered with power, hardware, access, and configuration.
To Next Page