Mass (g)
H4A = 130
H505B = 165
H510A = 180 H510B = 165 H510F = 200 H510P3E = 205
H520A = 210 H520B = 195 H520F = 230 H520P3E = 235
H520AH02 = 250
H540A = 285 H540B = 270 H540P3E = 310
H31A 300 = 190 H31P3 300 = 285 H31B 300 = 175
HY51
HY52
HY55
3M™ Peltor™
Hygiene Model
H505B, H510A, H510F, H510B, H510P3
H520A, H520B, H520F, H520P3
H520AH02
HY54H540A, H540B, H540P3
HY52H31A, H31P3
HY6H4A
Hygiene Kits
CLEANING INSTRUCTIONS
1. At the end of each shift the cushions of the ear muffs should
be wiped with a suitable material, for example 3M™ 105 Face
Seal Cleaners, so they remain clean and hygienic. The product
can also be cleaned using mild detergent and water.
2. If the ear muffs cannot be cleaned or are damaged, dispose of
the product and obtain a new pair.
3. Cushions and inserts can be replaced using the following
Hygiene Kits as shown below.
Remove the cushions and inserts as shown. See Figure 10.
Replace the worn or damaged cushions and insert with the
new pair from the appropriate hygiene kit.
4. Replace the product within 5 years from the date of
manufacture or immediately if damaged.
NOTE
In addition to the hygiene kit shown, 3M™ Peltor™ HY100 sweat
pads are also available that can be applied onto the ear muff
cushions to help absorb sweat and moisture for improved
comfort and hygiene. See Figure 10.
STORAGE AND TRANSPORTATION
Follow the manufacturers recommendation for storage.
Store the product in a clean dry area before and after use.
Always store the product in the original packaging and away from
any sources of direct heat or sunlight.
When stored ensure the headband is not stretched (applies to
headband version) and the cushions are not compressed as this
may damage the product.
When transporting use original packaging.
Check packaging for further information.
{
Date of Manufacture
\
Temperature Range
,
Maximum Relative Humidity
:
Name and address of Manufacturer
J Dispose of in accordance with local regulations
S/M/L (in a box with a tick): Indicates ear muffs meet medium
size range.
(DUPXIIVPHHWLQJPHGLXPVL]HUDQJH¿WSHRSOHZLWKVPDOO
medium and large head sizes.
See packaging for further information.
APPROVALS
These products meet the Basic Safety Requirements as laid out
in Annex II of the European Community Directive 89/686/EEC,
and have been examined at the design stage by: Finnish Institute
of Occupational Health (FIOH), Topeliuksenkatu 41aA,
),1+HOVLQNL)LQODQG1RWL¿HG%RG\QXPEHU
INSPEC International Limited, 56 Leslie Hough Way, Salford,
*UHDWHU0DQFKHVWHU0$-8.1RWL¿HG%RG\QXPEHU
&RPELWHFK$%%R[6(-RQNRSLQJ6ZHGHQ1RWL¿HG
Body number 2279 )
MATERIAL LISTING
Component Headband Version Neckband version: Helmet Mounted Version
Helmet Attachment Arm
Stainless Steel wire, PVC,
Acetal
6WDLQOHVVVWHHOZLUH3RO\ROH¿Q
Acetal
Cups
ABS
PVC PVC PVC
Polyether Polyether Polyether
ABS ABS
Inserts
Cushions
Cushion Covers
Polyether or Polyether and
Glycerine
Polyether or Polyether and
Glycerine
Polyether or Polyether and
Glycerine
Stainless Steel wire, Acetal,
Polyamide
Band
N/A N/A
N/A
3M™ Peltor™ Ear Muff
Model
6
To Next Page
Loading...
