ABB RTU560 User Manual

RTU560

Connections and Settings
Communication Unit 560CMD11
Doc.-No.: 1KGT 150 765 V005 1 1
Application, characteristics and technical data
have to be taken from the hardware data sheet:
560CMD11 R0001 1KGT 150 764 V0011
560CMD11 R0011 1KGT 150 764 V0011
Operation
The Communication Unit 560CMD11 is one of the
CMU boards (CMU = communication unit) of the
remote terminal unit RTU560. The 560CMD11
controls process events and communications with
control centers and local MMI systems via up to
four serial Interfaces (CP1, CP2, CPA, CPB), two
Ethernet 10BaseT/100BaseT LAN Interfaces (E1,
E2) and an integrated GPRS modem.
Fig. 1: Block diagram 560CMD11
To force the IP-Address to a default value at start-
up, the “Def. IP-Addr” switch on the front side (see
Fig. 8) has to be switched “ON”.
The 560CMD11 starts with the factory settings for
the Ethernet Interface (see Fig. 2) which are
192.168.0.1 for the IP-address with the network
setting 255.255.255.0 for the subnet mask and
192.168.0.20 for the gateway.
Switch „Def. IP- Address“
position
?
OFF
E
Read IP address
from confi-
guration file
ON
Set Switch
„Def. IP-Address“
to „OFF“
Send Configuration
to RTU 192.168.0.1
Switch „Def. IP- Address“
position
?
OFF
E
Read IP address
from confi-
guration file
ON
Set Switch
„Def. IP-Address“
to „OFF“
Send Configuration
to RTU 192.168.0.1
Fig. 2: Use Switch „Def. IP-Addr“
Serial Interface
The serial interfaces (CP1, CP2, CPA and CPB)
are available on the RJ45 connector on the front
plate. It can interface RS485 (Tab. 1) or RS232C
(Tab. 2) signals.
Serial Interfaces RS485 Mode
Pin
Signal
RJ45
1
8
Rx
Tx
RJ45
1
8
RJ45
1
8
Rx
Tx
Jack
1
-
Not used
2
TA
Data -
3
TB
Data +
4
-
Not used
5
GND
Signal Ground
6
-
Not used
7
-
8
-
Table 1: Serial Interfaces RS485 Mode

ABB RTU560 Specifications

General

Category	Remote Terminal Unit (RTU)
Manufacturer	ABB
Model	RTU560
Communication Ports	Ethernet, Serial, USB
Operating Temperature	-40°C to +70°C
Mounting	DIN rail
Communication Protocols	IEC 60870-5-101, IEC 60870-5-104, DNP3, Modbus
Certifications	UL
Power Supply	24V DC or 110-230V AC

Summary

Operation

Serial Interface RS485 Mode

Describes the RS485 serial interface pinout and signal assignments for the 560CMD11.

Serial Interfaces and GPRS Modem

Serial Interface RS232C Mode

Details the RS232C serial interface pinout and signal assignments for the 560CMD11.

GPRS Modem Functionality

Covers the 560CMD11 R0011 GPRS modem, its frequency bands, and SIM card requirements.

Ethernet, IO-Bus, and Power Supply

Ethernet Interface E1 and E2

Explains the functions and signal table for the RJ45 Ethernet interfaces on the 560CMD11.

Power Supply DC-In and DC-Out

Details the 24VDC power supply, connector specifications, and output power capabilities.

560CMD11 Earthing

Provides guidance on connecting the 560CMD11 to system earth for safety and EMC protection.

System Status and Power Connection

Signaling LEDs

Defines the system LEDs (ERR, PF, RUN, GPRS) and their meanings on the 560CMD11.

Power Supply Terminal X38

Describes the power supply terminal X38 and its connection to the housing ground.

Firmware and SIM Card Management

Firmware Version

Instructions for updating firmware via a CompactFlash memory card on the 560CMD11.

SIM-Card (only R0011)

Procedure for inserting and removing the SIM card for GPRS modem communication.

Configuration and RF Sensitivity

Settings for Protocols and Interfaces

Defines parameters for all protocols, Ethernet, and GPRS modem settings via RTUtil560.

RF Sensitivity Parameters

Lists transmitter parameters and provides an RF signal calculation for the GPRS modem.