Abrams SlickEye Visor User Manual

844.9.ABRAMS
INFO@ABRAMS-MFG.COM
WWW.ABRAMSMFG.COM
"#3".44-*$,&:&7*403-*()5#"3
*/45"--"5*0/"/ %  $ 0 / ' * ( 6 3"5*0/."/6"-
t PROPER INSTALLATION OF THIS PRODUCT REQUIRES THE
INSTALLER TO HAVE A GOOD UNDERSTANDING OF AUTOMOTIVE
ELECTRONICS, SYSTEMS AND PROCEDURES.
t
THIS PRODUCT CONTAINS HIGH-INTENSITY LEDS. DO NOT STARE
DIRECTLY INTO THESE LIGHTS. MOMENTARY BLINDNESS AND/OR
EYE DAMAGE COULD RESULT.
tt DO NOT INSTALL THIS PRODUCT OR ROUTE ANY WIRES IN THE
DEPLOYMENT AREA OF YOUR AIR BAG. EQUIPMENT MOUNTED OR
LOCATED IN THE AIR BAG DEPLOYMENT AREA WILL DAMAGE OR
REDUCE THE EFFECTIVENESS OF THE AIR BAG, OR BECOME A
PROJECTILE THAT COULD CAUSE SERIOUS PERSONAL INJURY OR
DEATH. REFER TO YOUR VEHICLE OWNER MANUAL FOR THE AIR
BAG DEPLOYMENT AREA. THE USER/INSTALLER ASSUMES FULL
RESPONSIBILITY
RESPONSIBILITY TO DETERMINE PROPER MOUNTING LOCATION,
BASED ON PROVIDING ULTIMATE SAFETY TO ALL PASSENGERS
INSIDE THE VEHICLE.
t IF MOUNTING THIS PRODUCT REQUIRES DRILLING HOLES, THE
INSTALLER MUST BE SURE THAT NO VEHICLE COMPONENTS OR
OTHER VITAL PARTS COULD BE DAMAGED BY THE DRILLING
PROCESS. CHECK BOTH SIDES OF THE MOUNTING SURFACE
BEFORE DRILLING BEGINS. ALSO DE-BURR ANY HOLES AND
REMOVE ANY METAL SHARDS OR REMNANTS. INSTALL
GROMMETS INTO ALL WIRE PASSAGE HOLES.
t INSPECT AND OPERATE THIS PRODUCT REGULARLY TO
CONFIRM ITS PROPER OPERATION AND MOUNTING CONDITION.
DO NOT USE A PRESSURE WASHER TO CLEAN THIS PRODUCT.
tt
FOR THIS PRODUCT TO OPERATE AT OPTIMUM EFFICIENCY, A
GOOD ELECTRICAL CONNECTION TO CHASSIS GROUND MUST BE
MADE. THE RECOMMENDED PROCEDURE REQUIRES THE
PRODUCT GROUND WIRE TO BE CONNECTED DIRECTLY TO THE
NEGATIVE (-) BATTERY POST.
tt IT IS RECOMMENDED THAT THESE INSTRUCTIONS BE STORED IN
A SAFE PLACE AND REFERRED TO WHEN PERFORMING
MAINTENANCE AND/OR REINSTALLATION OF THIS PRODUCT.
t FAILURE TO FOLLOW THESE SAFETY PRECAUTIONS AND
INSTRUCTIONS COULD RESULT IN DAMAGE TO THE PRODUCT OR
VEHICLE AND/OR SERIOUS INJURY TO YOU AND YOUR
PASSENGERS!
tt  IF THIS PRODUCT USES A REMOTE DEVICE TO ACTIVATE OR
CONTROL THIS PRODUCT, MAKE SURE THAT THIS CONTROL IS
LOCATED IN AN AREA THAT ALLOWS BOTH THE VEHICLE AND THE
CONTROL TO BE OPERATED SAFELY IN ANY DRIVING CONDITION.
t
DO NOT ATTEMPT TO ACTIVATE OR CONTROL THIS DEVICE IN A
HAZARDOUS DRIVING SITUATION.
IMPORTANT:
PLEASE READ ALL OF THE FOLLOWING INSTRUCTIONS BEFORE INSTALLING YOUR NEW ABRAMS SLICKEYE VISOR LIGHTBAR
WARNING:
FAILURE TO INSTALL OR USE THIS PRODUCT ACCORDING TO MANUFACTURER’S RECOMMENDATIONS MAY RESULT IN PROPERTY
DAMAGE, SERIOUS INJURY, AND/OR DEATH.
WIRING CONFIGURATION / OPERATION WITH CIGARETTE PLUG (OPTIONAL)

Abrams SlickEye Visor Specifications

General

Category	Automobile Accessories
Type	Visor
Material	Polycarbonate
Scratch Resistance	Yes
Compatibility	Universal
Color Options	Smoke, Clear

Summary

Important Safety and Installation Guidelines

General Installation Prerequisites

Requires understanding of automotive electronics and systems for proper installation.

LED Eye Safety

High-intensity LEDs require avoiding direct stares to prevent blindness or eye damage.

Air Bag Deployment Area

Do not install or route wires in air bag deployment areas to prevent damage or injury.

Drilling Precautions

Ensure no vehicle components are damaged during drilling; de-burr holes and use grommets.

Regular Inspection and Maintenance

Inspect product regularly for proper operation and mounting; avoid pressure washers.

Grounding Connection

Connect product ground wire directly to the negative battery post for optimal efficiency.

Instruction Storage

Store instructions safely for future reference during maintenance or reinstallation.

Remote Device Operation

Ensure remote control is located safely for operation in any driving condition.

Hazardous Driving Situations

Do not attempt to activate or control the device in a hazardous driving situation.

General Warning

Consequences of Improper Installation/Use

Failure to follow recommendations may result in property damage, serious injury, or death.

Wiring Configuration and Operation

Cigarette Plug Operation

Plug unit into socket, turn on power, select pattern via selector switch.

Hardwire Setup

Connect specific wires (Red, Black, White, Yellow) for power, ground, sync, and pattern selection.

Synchronizing Multiple Units

Connect desired pattern wire with 12VDC, then connect white wires of all units together.

Mounting Instructions

Visor Bracket Attachment

Use supplied mounting brackets to attach light bar to vehicle visor; modification may be needed.

Troubleshooting

Common Issues

Check power source connections, short circuits, power switch state, and pattern selection.

Warranty Information

Five-Year Limited Warranty

Covers defects for 5 years; voided by improper installation, abuse, or accidents.