ACTi D11 - User Manual

Other manuals for ACTi D11

Hardware Manual23 pages

Need help?

Do you have a question about the ACTi D11 and is the answer not in the manual?

Summary

0. Precautions

FCC;CE Regulation

NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules.

1. Introduction

Package Contents

Lists all items included in the product package for initial setup.

Features and Benefits

This is a cutting-edge digital video surveillance camera. It can compress and transmit real time images.

Safety Instructions

Do not open the housing of the product. Disconnect power before cleaning. Avoid water and moisture.

Physical description

Details the Reset Button and Ethernet Port on the device, including their functions and operation.

Basic Connections

Instructions on how to connect the IP device to a PoE switch/injector and PC using network cables.

Product Specification

Detailed technical specifications for the D11 Cube Camera, including device, lens, video, network, and general properties.

2. Accessing Camera

Accessing Camera with DHCP

Connect the IP Camera to a network with a DHCP server; the device will acquire an IP address automatically.

Accessing Camera without DHCP

Configure PC's IP to 192.168.0.XXX and use default camera IP 192.168.0.100.

This document is the Hardware User's Manual for the ACTi D11 1MP Cube Camera with a fixed lens and PoE support, released on 2012/10/19.

The ACTi D11 is a cutting-edge digital video surveillance camera designed for intelligent IP surveillance systems. It offers real-time image compression and transmission over a standard TCP/IP network with outstanding image quality.

Important Technical Specifications:

Device:

Device Type: Cube Camera
Image Sensor: Progressive Scan CMOS
Day/Night: No
Minimum Illumination: Color: 0.1 lux at F2.0 (30 IRE, 2400 °K)
Mechanical IR Cut Filter: No
IR Sensitivity Range: No
Electronic Shutter: 1/5 - 1/2,000 sec (Manual / Auto mode)

Lens:

Focal Length / Aperture: Fixed focal, f3.6 mm / F2.0
Iris: Fixed iris
Focus: Fixed focus
Mount Type: Board Mount
Horizontal Viewing Angle: 61°

Video:

Compression: H.264 HP, MJPEG
Maximum Frame Rate vs. Resolution: 30 fps at 1280 x 720 (HD 720p); 30 fps at 640 x 480 (VGA)
Multi-Streaming: Simultaneous dual streams based on two configurations
Bit Rate: 28 Kbps - 6 Mbps (per stream)
Bit Rate Mode: Constant, Variable
Image Enhancement: White balance: automatic, hold and manual; Brightness; Contrast; Automatic gain control; Digital noise reduction; Flickerless
Privacy Mask: 4 configurable regions
Text Overlay: User defined text on video
Image Orientation: Image flip and mirror

Network:

Protocol & Service: TCP, UDP, HTTP, HTTPS, DHCP, PPPoE, RTP, RTSP, IPv6, DNS, DDNS, NTP, ICMP, ARP, IGMP, SMTP, FTP, UPnP, SNMP, Bonjour
Ethernet Port: 1, Ethernet (10/100 Base-T), RJ-45 connector
Security: IP address filtering; HTTPS encryption; Password protected user levels; IEEE 802.1X network access control

Alarm:

Alarm Trigger: Video motion detection (3 regions)
Alarm Response: Notify control center; Change camera settings; Command other devices; E-mail notification with snapshots; Upload video, snapshot to FTP server

General:

Power Source / Consumption: PoE Class 1 (IEEE802.3af) / 2.95 W
Weight: 140 g (0.31 lb)
Dimensions (Φ X H): 66.50 mm x 103.95mm x 38.75mm (2.62" x 4.09" x 1.53")
Bundled Accessories: Bracket
Mount Type: Wall, Ceiling
Operating Temperature: -10°C ~ 45°C (14°F ~ 113°F)
Operating Humidity: 10% ~ 85% RH
Approvals: CE, FCC

Integration:

Unified Solution: Fully compatible with ACTi software
ISV Integration: Software Development Kit (SDK) available; ONVIF compliant
Firmware Access Browser: Microsoft Internet Explorer 6.0 or newer

Usage Features:

H.264 High Profile/MJPEG Multi-Codec Dual Streaming: The D11 supports two compression formats, H.264 High Profile and MJPEG, delivering superior image quality at 30 frames per second up to 720p (1280 x 720) and VGA (640 x 480) resolutions.
Built-in Hardware Motion Detection: Eliminates the need for external motion sensors. Users can define up to three video motion detection areas and tune object size and sensitivity for reliable detection. Hardware motion detection offers better sensitivity and faster response times compared to software detection.
Powerful Bundled Surveillance Software: The camera comes with a free surveillance program that allows users to convert an existing PC into a digital video recorder. Features include scheduled and manual recording, reliable motion detection with instant warnings, and quick search and playback functions.
Software Development Kit (SDK) Support: The D11 can be integrated or controlled by third-party software applications. ACTi provides a Streaming Library or ActiveX control to assist developers, saving considerable effort.

Maintenance Features:

Reset Button: A reset button is available on the device. Pressing and holding it for 15 seconds after the unit has booted will reset the device to factory default settings. The Ethernet LED will indicate the completion of the reset process.
Servicing: Do not attempt to service the device yourself. Opening or removing covers may expose users to dangerous voltage or other hazards. All servicing should be referred to qualified service personnel.
Safety Check: After any service or repairs, a safety check should be performed by a service technician to ensure the device is in proper operating condition.
Cleaning: Disconnect the video product from the power supply before cleaning.
Connectivity: The camera connects to the Ethernet via a standard RJ45 connector, supporting NWAY for auto-detection of 10Base-T/100Base-TX Ethernet speeds. It is designed to be powered over Ethernet (PoE Class 1, IEEE802.3af).
IP Address Configuration: For networks with a DHCP server/router, the camera will automatically acquire an IP address. For networks without DHCP, the user must manually configure the PC's IP address to the same subnet (e.g., 192.168.0.XXX) and then access the camera via its default IP (192.168.0.100). If multiple devices are used, their IP addresses must be changed to unused static IPs to avoid conflicts.
Firmware Access Browser: The device firmware can be accessed and configured using Microsoft Internet Explorer 6.0 or newer.