ActionTec Verizon GT784 User Manual

Instructions to Connect
your New Gateway Router
The Verizon GT784 gateway/router is
replacing your current 6110 Bridged device.
Please note: This process below should be
followed only if you are attaching another piece
of equipment (router/switch, etc) to this Verizon
Gateway GT784. If your existing set up requires
the Verizon GT784 to be put in bridge mode,
please follow these quick easy steps.
If you congure the Verizon GT784 in bridge mode, this will
disable the wireless functionality.
1
2
3
4
5
6
7
8
9
10
11
The “Login” screen will appear
• Create and enter a new password for the Verizon GT784
• “Re-type the New Password” in the appropriate eld
• Make sure to write the password down on a piece of paper
and keep it in a safe place for future reference
• Select your local time zone from the “Time Zone” drop-
down list
• Click Apply
1
2
3
4
5
6
7
8
9
10
11
Advanced Setup
• After the changes are applied, the Verizon GT784 Home
screen will appear.
• Click on the Advanced Setup tab located at the top of the screen
1
2
3
4
5
6
7
8
9
10
11
Advanced Setup Screen will Appear
• Click on “WAN IP Settings” located under “IP Addressing”
Before You Begin
Disconnect your existing Verizon modem/router including all
cables and cords and any other equipment attached to the
Verizon modem/router.
1
2
3
4
5
6
7
8
9
10
11
CONFIGURING BRIDGE MODE
Logging in to the Verizon GT784
To access the Verizon GT784, enter the following gateway
address into the browser address line: http://192.168.1.1
1
2
3
4
5
6
7
8
9
10
11
ROUTER SETUP
Connecting your new gateway/router
A
Connect Yellow Ethernet cord from Ethernet port on PC
or laptop to any of the 4 Ethernet ports on the back of the
wireless router
B
Connect phone line to phone jack and wireless router
• Do not place a lter on phone line connected to the
router
• Use a 2-for-1 adapter If connecting a phone on the
same jack.
• Make sure to place a lter on the line connected to
the telephone
C
Connect Power supply to router and plug into power outlet
D
Turn router on using the power on/o switch
1
2
3
4
5
6
7
8
9
10
11
A
D
B
C
REPINST6110

ActionTec Verizon GT784 Specifications

General

Wireless Standard	802.11b/g/n
Frequency Band	2.4 GHz
Security	WEP, WPA, WPA2
DSL Standard	ADSL2+
Firewall	Yes
Max Transfer Rate	300 Mbps
Brand	Actiontec
Model	GT784
DSL Compatibility	ADSL, ADSL2, ADSL2+
LAN Ports	4
WAN Port	1
Device Type	Wireless Router

Summary

Before You Begin

ROUTER SETUP Connecting your new gateway/router

Connect Network and Power

Connect Ethernet, phone line, and power supply to the router and outlet.

CONFIGURING BRIDGE MODE Logging in to the Verizon GT784

Access Gateway for Login

Enter the gateway address http://192.168.1.1 in your browser to log in.

The "Login" screen will appear

Set New Password and Time Zone

Create a new password, confirm it, and select your local time zone on the login screen.

Advanced Setup Access

Navigate to Advanced Setup Tab

Click on the Advanced Setup tab located at the top of the screen.

Advanced Setup Screen Navigation

Select WAN IP Settings

Click on 'WAN IP Settings' under 'IP Addressing' in the Advanced Setup screen.

WAN IP Settings Configuration

Configure RFC 1483 Transparent Bridging

Select RFC 1483 Transparent Bridging and click Apply on the WAN IP Settings page.

Configuration Completion

Access Utilities Tab

Click on the Utilities tab to access further options after setup.

Gateway Reboot Procedure

Reboot the Gateway

Click on the 'Reboot' button in the Utilities screen or power cycle the device.

DSL Gateway Reboot Warning

Complete Reboot Process

Close config window, wait 2 minutes, then reopen browser.