Acuity Controls Sensor Switch WSX D User Manual

INSTRUCTION
SHEET
© 2015 Acuity Brands Lighting Inc., All Rights Reserved.12/2015
SPECIFICATIONS
PHYSICAL SPECS
SIZE: 2.74”H x 1.68”W x 1.63”D
(6.96 cm x 4.27 cm x 4.14 cm)
(not including ground strap)
WEIGHT: 5 oz
MOUNTING: Single Gang Switch Box
MOUNTING HEIGHT: 30-48 in (76.2-121.9 cm)
ELECTRICAL SPECS
MAXIMUM LOAD (Relay)
800 W @ 120 VAC / 1200 W @ 277 VAC / 1500 W @ 347 VAC
MINIMUM LOAD: None
MOTOR LOAD: 1/4 HP
MAX SINK CURRENT: 50 mA
010V DIM MIN OUTPUT: <0.3 V
FREQUENCY: 50/60 Hz (timers are 1.2x for 50 Hz)
ENVIRONMENTAL SPECS
OPERATING TEMP: 14° to 122° F (-10° to 50° C)
RELATIVE HUMIDITY: 20 to 75% non-condensing
ROHS COMPLIANT
WSX D
Dimming Occupancy Wall
Switch
CONVERSION FROM GROUND ONLY NO NEUTRAL TO NEUTRAL WIRING
This product is pre-configured for wiring without a neutral; however, if connection to neutral is required by
code, the unit easily converts in seconds.
Step 1:
Remove Yellow
Label
Step 2:
Loosen Screws and
Remove Metal Link
Step 3:
Connect Neutral to
Silver Screw & Ground
to Green Screw
WIRING TO GROUND NO NEUTRAL WIRING TO NEUTRAL
36 30 20 10 0 ft 10 20 30 36
12 9 6 3 0 m 3 6 9 12
Small
motion
detection
Small
motion
detection
to ~20 ft
6
3
0 m
20
10
0 ft
Small motion ~40 ft coverage
TOP VIEW
1.2 m
4 ft
Small motion
detection to ~20 ft
Large motion detection to >36 ft
SIDE VIEW
0 18 27 369
ft
0 6 9 123
m
TOP VIEW
36 30 20 10 0 ft
10 20
30 36
12 9 6 3 0 m
3 6 9 12
Small
motion
detection
Small
motion
detection
to ~20 ft
6
3
0 m
20
10
0 ft
Small motion ~40 ft coverage
TOP VIEW
1.2 m
4 ft
Small motion
detection to ~20 ft
Large motion detection to >36 ft
SIDE VIEW
0 18 27 369
ft
0 6 9 123
m
GND
H
N
LOAD
BLK
BLK
REMOVE METAL LINK
IF CONNECTING TO
NEUTRAL
VIO (+)
GRY (-)
DIMMING
H
N
LOAD
BLK
BLK
N
GND
VIO (+)
GRY (-)
DIMMING
120/277 VAC WIRING
BLACK* - Line Input
BLACK* - Load Output
VIOLET -Low Voltage Dim Output (0-10 VDC)
GRAY -Low Voltage Common
*BLACK wires
can be reversed
}
WIRE COLOR KEY
347 VAC WIRING (-347 Option)
Red wires replace Black wires.
NOTES:
1.) Per NEC requirements, the 0-10V violet and gray wires must be installed as Class One.
2.) The 0-10V control wires must not exceed 250 ft (76 m) in length and must be sized at no less than 20 AWG.
COVERAGE PATTERN
• Small motion (e.g. hand movements) detection up to 20 ft (6.10 m), ~625 ft
2
• Large motion (e.g. walking) detection greater than 36 ft (10.97 m), ~2025 ft
2
• Wall-to-wall PIR coverage
• Units with -PDT (Passive Dual Technology) option (also called Microphonics
TM
) provide overlapping detection
of human activity over the complete PIR coverage area. Advanced filtering is utilized to prevent non-occupant
noises from keeping the lights on.
911-00059-003

Acuity Controls Sensor Switch WSX D Specifications

General

Brand	Acuity Controls
Model	Sensor Switch WSX D
Category	Lantern
Language	English

Summary

Coverage Pattern

Wiring Conversion and Diagrams

Conversion From Ground Only to Neutral Wiring

Procedure to convert the product from ground-only wiring to neutral wiring for code compliance.

Wiring Schematics

Illustrates wiring connections for both 'No Neutral' and 'Neutral' configurations.

Specifications Overview

Physical Specifications

Details dimensions, weight, and recommended mounting height for the device.

Electrical Specifications

Covers load ratings, motor load, sink current, and dimming output parameters.

Environmental Specifications

Defines operating temperature, relative humidity, and compliance standards.

Adaptive Daylight Harvesting (ADH)

Programming Instructions

Select New Setting

Guide on how to select and set new operational parameters via push-button sequences.

Reselect Function to Save

Instructions for reselecting functions and saving programmed settings.

Operational Settings

Occupancy Time Delay Settings

Configures the time delay before lights turn off after no occupancy is detected.

On Mode and Switch Modes

Sets automatic/manual operation and defines switch override behaviors.

Daylight and Darkness Set-Points

Establishes ambient light levels for automatic dimming control.

Photocell and Dim to Off Settings

Manages photocell inhibition and time lights stay at low dim before turning off.

Dimming Range and Predictive Settings

Configures minimum/maximum light output and predictive mode timing.

Grace Periods and Fade Rates

Sets time for voice reactivation and light transition speeds.

LED Operation and Dual Technology

Controls LED indicator behavior and secondary detection method.