What to do if unable to save the assigned frequency to non-volatile memory in ADB Control Unit?
If you are unable to save the assigned frequency to non-volatile memory in your ADB Control Unit, you should replace the Radio Control Board.
What to do if ADB Control Unit is unable to save to the RTC chip?
If the ADB Control Unit is unable to save to the RTC chip, causing the power outage logic not to restore the commanded lighting state, you should replace the Radio Control Board.
What to do if the synthesizer is not indicating that it is locked to it’s assigned frequency in ADB L-854 Control Unit?
If the ADB Control Unit's synthesizer is not indicating that it is locked to its assigned frequency, you should replace the Radio Control Board.
What to do if 3.3 volt power is below 3.0V DC in ADB Control Unit?
If the 3.3 volt power is below 3.0V DC in your ADB Control Unit, you should replace the Power Supply Board.
What to do if 3.3 volt power is above 3.6V DC in ADB Control Unit?
If the 3.3 volt power is above 3.6V DC in your ADB Control Unit, you should replace the Power Supply Board.
What to do if 5 volt power is below 4.7V DC in ADB Control Unit?
If the 5 volt power is below 4.7V DC in your ADB Control Unit, you should replace the Power Supply Board.
What to do if 5 volt power is above 5.3V DC in ADB Control Unit?
If the 5 volt power is above 5.3V DC in your ADB Control Unit, you should replace the Power Supply Board.
General| Brand | ADB |
|---|---|
| Model | L-854 |
| Category | Control Unit |
| Language | English |
Details CE certification compliance with essential safety and hygiene requirements.
Details ETL certification compliance with essential safety and FAA regulations.
Specifies warranty terms for LED airfield guidance signs and light fixtures.
Outlines warranty for ADB products against mechanical, electrical, and physical defects.
Covers ADB LED products meeting FAA, ICAO, and IEC requirements.
Explains hazard symbols used in the manual for safety warnings.
Defines qualified personnel and responsibilities for safe operation and maintenance.
Lists relevant standards and codes for safe equipment installation and use.
Specifies the intended use of the equipment and warns against improper operation.
Provides warnings regarding the use and tightening of fasteners to prevent damage.
Details safe operation practices, including personnel qualifications and environmental conditions.
Provides instructions for proper storage of equipment prior to installation.
Outlines precautions for handling electrostatic sensitive devices and unstable loads.
Describes actions to take in case of system or component malfunctions.
Highlights safety precautions during maintenance, especially electrical hazards.
Lists safety requirements for qualified personnel performing maintenance and repair.
Introduces the purpose and scope of the L-854 Radio Control Equipment manual.
Provides guidance on how to effectively work with the content of the manual.
States compliance with FCC Part 15 rules and operating conditions.
Describes available options for the L-854 Radio Control Equipment.
Lists supplied and required equipment and accessories for installation.
Defines where and when the air-to-ground Radio Control can be used.
Explains how to connect the Radio Controller to other airfield systems.
Describes the main components of the L-854 Radio Control Equipment.
Details the terminal block's function for interfacing with other equipment.
Provides instructions for unpacking and inspecting the equipment upon receipt.
Details the steps for installing the standard L-854 Radio Control Equipment.
Instructions for connecting the remote antenna to the radio unit.
Highlights critical safety warnings for antenna installation near power lines.
Provides guidance on securely mounting the antenna and its mast.
Describes the controls and indicators on the L-854 Radio Control Equipment.
Step-by-step guide for powering up and configuring the L-854 Radio Control Equipment.
General guidance on maintenance, referring to the Theory of Operation section.
Instructions on how to set or change the operational frequency of the receiver.
Lists the available wiring diagrams for the L-854 Radio Control Equipment.
Provides an overview of the parts covered in this section.
Explains how to use the parts list for ordering components.
Details the ordering code structure for the L-854 Radio Control Equipment.
To Next Page