ADC AD-230 User Manual

AD-230/AD-235
Installation/Operator's Manual
ADC Part No. 112160
For replacement parts, contact the distributor from which the dryer
was purchased or
American Dryer Corporation
88 Currant Road
Fall River MA 02720-4781
Telephone: (508) 678-9000 / Fax: (508) 678-9447
E-mail: techsupport@amdry.com
040194
101398SL/mt
WARNING: For your safety the
information in this manual must be
followed to minimize the risk of fire or
explosion or to prevent property damage,
personal injury or death.
Do not store or use gasoline or other flammable
vapor and liquids in the vicinity of this or any
other appliance.
WHAT DO YOU DO IF YOU SMELL GAS
* Do not try to light any appliance.
* Do not touch any electrical switch; do not use
any phone in your building.
* Clear the room, building or area of all
occupants.
* Immediately call your gas supplier from a
neighbor's phone. Follow the gas supplier's
instructions.
* If you cannot reach your gas supplier, call the
fire department.
Installation and service must be performed by a
qualified installer, service agency or the gas
supplier.
AVERTISSEMENT: Assurez-vous de bien
suivre les instructions données dans cette
notice pour réduire au minimum le risque
dincendie ou dexplosion ou pour éviter tout
dommage matériel, toute blessure ou la mort.
Ne pas entreposer ni utiliser dessence ni
dautres vapeurs ou liquides inflammables dans
le voisinage de cet appareil ou de tout autre
appareil.
QUE FAIRE SI VOUS SENTEZ UNE ODEUR
DE GAZ:
* Ne pas tenter dallumer dappareil.
* Ne touchez à aucun interrupteur. Ne pas
vous servir des téléphones se trouvant dans
le bâtiment où vous vous trouvez..
* Évacuez la pièce, le bâtiment ou la zone.
* Appelez immédiatement votre fournisseur de
gaz depuis un voisin. Suivez les instructions
du fournisseur.
* Si vous ne pouvez rejoindre le fournisseur
de gaz, appelez le service des incendies.
Linstallation et lentretien doivent être assurés
par un installateur ou un service dentretien
qualifié ou par le fournisseur de gaz.

ADC AD-230 Specifications

General

Brand	ADC
Model	AD-230
Category	Dryer
Language	English

Summary

Important Information

Receiving and Handling

Details on inspecting and handling dryers upon receipt to identify and report shipping damage.

Safety Precautions

Covers essential safety guidelines, warnings, and procedures for operating the dryer.

Installation Procedures

Unpacking and Setting Up

Instructions for removing shipping materials, handling keys, and preparing the dryer for placement.

Location of the Dryer

Guidelines for selecting a suitable location, considering codes, clearances, and environmental factors.

Dryer Enclosure Requirements

Specifications for clearances, materials, and ventilation around the dryer enclosure.

Fresh Air Supply

Requirements for adequate make-up air for proper dryer operation and performance.

Exhaust Requirements

Guidelines for designing and installing exhaust duct work for safe and efficient operation.

Electrical Information

Details on electrical requirements, grounding, and wiring connections for the dryer.

Gas Information

Information on gas supply, types of gas, and piping connections for gas models.

Preparation for Operation

Checklist of tasks to perform before operating the dryer for the first time.

Shut Down Instructions

Procedure for safely shutting down the dryer for an extended period.

Operating Instructions

Starting the Dryer

Step-by-step guide on how to start the dryer and select operating settings.

Service and Parts Information

Service

Information on obtaining service and contacting qualified technicians.

Parts

Guidance on ordering replacement parts from distributors or the factory.

Warranty Information

Returning Warranty Card(s)

Instructions for completing and returning the dryer's warranty card.

Warranty

Information on obtaining a copy of the commercial warranty for the dryer.

Returning Warranty Parts

Procedures for returning warranted parts for processing and resolution.

Routine Maintenance

Cleaning

Schedule and instructions for cleaning lint and debris from the dryer and ductwork.

Adjustments

Guidelines for inspecting and adjusting components after installation and periodically.

Lubrication

Information regarding lubrication requirements for dryer components.

Procedure for Functional Check of Replacement Components

Microprocessor (computer) Board

Steps to verify the functional check of a replacement microprocessor board.

Direct Spark Ignition (DSI) System

Procedure for performing a functional check on the Direct Spark Ignition (DSI) system.