Adcom GTP-600 User Manual

2) Press the RC-65 Learn key © to enter Learn mode. The Learn LED © glows steadily.
3> S° Pe ' R C ' 65 '" PUl SeleC ' °' bUt '°" “ ide " % ,he component. The Learn LED
4) Press the RC-65 command key you wish to program. The Learn LED blinks once.
5) thG corres P ° n< “jj n 9 k ey on the other remote until the RC-65 Learn LED blinks twice The
Learn LED then resumes steady operation.
m ' q 9 ,lu rr ° r ? J d i c a ted by simultaneous operation of Learn and Transmit LEDs. If this happens
repeat steps 3 through 5 as needed. ^
6) Repeat steps 3 through 5 above for all other desired commands.
7) When finished, press the Learn key to exit Learn mode. The Learn LED goes out.
C) To delete previously programmed commands (except non-erasable ADCOM commands):
1) Press the RC-65 Learn key © to enter Learn mode. The Learn LED© glows steadily.
2 ^ ^wice 0 ^^ RC ’ 65 lnpUt Selector button to identify the corresponding component. The Learn LED
3) Press the RC-65 Reset button©. The Learn LED blinks continuously
4) operation. R C ' 6 5 C ° mmand ^ Y ° U WiSh t0 dear ' The Learn LED st °P s ^king & resumes steady
of| te t YC \ L ' C , an del f e an entire bank of buttons < a l 1 command keys associated with a particular Input
belector) at once by pressing the appropriate Input Selector again.
5) Repeat steps 3 & 4 as desired.
6) Press the Learn key to exit Learn mode. Learn LED goes out.
ADVANCED OPERATION
26) K Y STE m B A L ANCING: AGCUrate balancin9 enhances the s P a tia( ^curacy of your audio/video playback system
by matching the acoustic levels of all system speakers in your room as closely as possible. Once you've done
his any level differences from left to center or from center to rear, etc., are differences intended
the original soundtrack, not some unwanted aberration caused by the acoustics of your room.
EVERY ROOM IS ACOUSTICALLY DIFFERENT AND THE RELATIVE CHANNEL-TO-CHANNFI I FVFi 6 wn i
'T«nge AS you move around the room, this means that you should perform thebauwce
CHECK WHILE SEATED IN YOUR FAVORITE LISTENING/VIEWING LOCATION. ThaTs why weVe^induded^Ihe
necessary center, rear, and subwoofer level adjustments ONLY on the RC-65 hand held remote controller.
A) Activate the "Balance check” circuit: Push the Bal check button © An internal signal generator interrupts
e normal audio information and sends a test tone to all loudspeakers sequentially The test tone is a filtered
broadband signal close in overall balance to the normal distribution of tones encountered in real iffe
Yh f!° n e 9 e n e r ator will “step” through all speakers sequentially beginning with the left front. After two seconds
of left front output, the tone will shift to the center channel.
B) cl5ily e as C poSble Vel Up/D ° Wn ” bUtt ° nS ® t 0 adjust center channel out P u t to match 'eft channel volume as
C) ?l e ; = i mat ^ T ? C .° ndS ' t h e C6nter Channel Wi " m u te and you ' " hear the test tone through the right
front speaker, probably at the same level as that of the left channel. If this is the case, do nothing. 9
OTP ?nn-c a h^ b S t antial , dlf !l en o Ce between left front and r ' g h t front outputs, correct the difference with the
GTP-600S balance control © Significant placement differences for left and right front speakers may cause
mJk'^ b th a n C | e: dea " y 5 l ey ah0uldbe spaced symmetrically on either side of the TV screen. If room decor
balaTOicorrecro ment ^ ' f Y ° U Pr6fer l ° Slt off ' center from the W screen, you may need left-right
13

Adcom GTP-600 Specifications

General

Brand	Adcom
Model	GTP-600
Category	Amplifier
Language	English