ADEMCO VIA-30PSE Installation Instructions

Name: ADEMCO VIA-30PSE
Brand: ADEMCO
Rating: 4 (1 reviews)

104 pages

To Next Page

THIS ISSUE INCLUDES THE NEW QED (QUICK ENROLLLMENT

OF DEVICES) PROCEDURE FOR 5800 SERIES TRANSMITTERS

VIA-30P

N7225V2 4/97

Installation Instructions • Installation Instructions • Installation Instructions

Security System

WWW.DIYALARMFORUM.COM

Default Chapter1
- Security System1
- Recommendations for Proper Protection2
- Table of Contents3
- How to Use this Manual7
- Conventions Used in this Manual8
Section 1. GENERAL DESCRIPTION9
Section 2. INSTALLING the CONTROL11
- Installing the Control's Circuit Board Alone or (if Used)11
- Installing the Lock (if Used)11
- Mounting the Cabinet11
- Installing Control and RF Receiver Circuit Boards Together in the Cabinet13
- Standard Phone Line Connections13
Section 3. INSTALLING REMOTE KEYPADS15
- Keypads that May be Used15
- Wiring to the Keypads15
  - Wiring Run Chart for Devices Drawing AUX Power from the Control15
- Figure 5. Keypad Connections to the Control Board16
- Mounting the Keypads16
- Using a Supplementary Power Supply to Power Additional Keypads16
- Preliminary Check-Out Procedure17
Figure 6. Using a Supplementary Power Supply for Keypads17
BASIC HARD-WIRED ZONES 5 and 619
- Installing the Hard-Wired Zones19
  - Common Characteristics for Zones 5 and 619
- Wiring Burglary and Panic Devices to Zones 5 and 619
- Wiring 4-Wire Smoke/Combustion Detectors on Zones 519
- Programming Hard-Wired Zones20
  - Programming Panic Keys21
- Check-Out Procedure for Hard-Wired Zones 5 and 622
Wired Zone Expansion (4219, 4229)23
- Connections and Setup23
- Installing Zone Expansion Units23
- Programming Wired Expansion Zones24
- Check-Out Procedure for Wired Expansion Zones25
- Wireless System Operation and Transmitter Supervision27
  - Transmitter Battery Life28
- Wireless Systems Available27
- Installation and Setup of the 4281/5881 Series Wireless Receivers28
- Receiver Supervision28
- 5700 Series Transmitter Setup29
  - Wireless Zone/ID Assignments for 5700 Series Transmitters30
- Installing the 5800TM Module29
- DIP Switch Tables for 5700 RF System Wireless Devices31
- Compatible 5700 Series Transmitters32
- Programming the Control for a 5700 Wireless System33
  - Using the House ID Sniffer Mode (5700 Systems)33
- Zone Programming for 5700 Series Transmitters33
  - Go/Nogo Test35
- 5800 Series Transmitter Setup36
- Compatible 5800 Series Transmitters37
- Programming the RF Transmitters (5800 RF Systems)38
- Enrolling 5800 Transmitters into the System39
  - Enrolling through Zone Programming ( 56)39
  - (5800 System)42
- Check-Out Procedure for Wireless Zones42
  - Figure 10. 4204 Connections to Control45
  - Figure 9. 4281, 5881, and 5882 Wireless Receivers (Cover Removed)45
  - Figure 8. Wiring Connections, 4219 and 4229 Expanders45
  - Figure 11: 4229 Connections to Control46
  - Programming Options Defined46
  - Programming Output Relays48
    - Example of Output Relay Programming49
- Relay Device Basics45
  - Supervision45
4285 Phone Module51
- Installing the Phone Module51
  - Phone Module Wiring51
  - Caller ID Units52
- Figure 12. 4285 Phone Module Wiring Connections53
- Programming the Control for Phone Access54
- Checking the Operation of the 4285 Phone Module55
External Sounders57
- Compatible Sounders57
- Sounder Connections58
- Programming for External Sounders58
- Testing the Sounder58
Figure 13. Typical Sounder Wiring58
Figure 14. Long Range Radio Connections59
Long Range Radio59
- General Information59
Audio Alarm Verification (Aav) Unit61
- General Information61
- Wiring Connections61
- Programming61
Figure 15. Connection of AAV Unit When Not Using a 4285 Phone Module62
Figure 16. Connection of AAV Unit When also Using a 4285 Phone Module62
Final Power up63
- Earth Ground Connections63
- AC Power-Up63
- Connecting the Back-Up Battery63
  - Calculating the Battery Size Needed63
  - Making the Battery Connections63
- Auxiliary Device Current Draw Worksheet64
Alpha Descriptor Programming65
- Assigning Zone Descriptors65
  - Entering Zone Descriptors (in Program Menu Mode 82)65
  - Programming the Descriptors65
- Alternate Method for Programming Zone Descriptors67
- Adding Custom Words68
- Alpha Vocabulary List (for Entering Zone Descriptors)69
- Character (ASCII) Chart69
Sequential Mode71
- (For 5800 Series Wireless Transmitters)71
System Communication75
- Report Code Formats75
  - Table of Contact ID Event Codes77
- Communication Programming77
Testing the System83
- Test Procedure83
- To the Installer84
System Operation85
- Security Codes85
- Keypad Functions86
- Trouble Conditions88
Troubleshooting Guide89
- Contacting Technical Support91
Specifications & Accessories93
- Specifications93
- Accessories (Compatible Devices)95
Appendix A: REGULATORY AGENCY STATEMENTS97
Appendix B: LIMITATIONS of this ALARM SYSTEM101
- Limited Warranty102
- Summary of Connections Diagram103

Other manuals for ADEMCO VIA-30PSE

Quick Guide4 pages

Programming Guide24 pages

Questions and Answers:

Need help?

Do you have a question about the ADEMCO VIA-30PSE and is the answer not in the manual?

ADEMCO VIA-30PSE Specifications

General

Power Supply	Transformer
Power Supply Voltage	16.5 VAC
Input Voltage	120 VAC
Output Voltage	12 VDC
Zones	8
Battery Backup	Yes
Operating Temperature	0°C to 49°C (32°F to 120°F)
Humidity	Up to 85% non-condensing

Related product manuals

ADEMCO VIA-30PSE Installation Instructions

Table of Contents

Other manuals for ADEMCO VIA-30PSE

Questions and Answers:

ADEMCO VIA-30PSE Specifications

Related product manuals