How to fix an ADJ stinger ii Light Fixture with no light output?
If there is no light coming from your ADJ Light Fixture, make sure that the external fuse hasn't blown. The fuse is located on the rear panel of the unit. Also, be sure the fuse holder is completely and properly seated.
What to do if my ADJ stinger ii does not respond to sound?
If your ADJ Light Fixture isn't responding to sound, ensure that low frequencies (bass) are present, as tapping on the microphone or using quiet, high-pitched sounds may not activate the unit. Also, verify the sound sensitivity level.
Details on unpacking, intro, customer support, general instructions, and features.
Critical warnings regarding electrical shock, fire, eye damage, and unit handling.
Avoid shock/fire risks, ensure ventilation, indoor use, and proper mounting.
Unit requires qualified service; avoid damage, spills, and abnormal operations.
Details risks of laser radiation, potential eye injury, and the importance of not opening the housing.
Do not point lasers at people/animals, avoid direct eye exposure, and use safe setup practices.
Automatic voltage switch and explanation of DMX-512 for lighting control.
Connecting DMX fixtures, setting addresses, and data cable specifications.
Importance of using a terminator on the last unit in a DMX chain to avoid erratic behavior.
Secure mounting with clamps, structure support, and use of safety cables.
Equipment must be installed by a professional in a safe, out-of-reach location.
How to navigate the menu, set DMX address, and understand basic operations.
Configuration for DMX channel, show, UV speed, sound active, and master/slave modes.
Display inversion, LED control, self-test, fixture hours, software version, and reset.
Using a DMX controller for patterns, rotation, and strobing effects.
Operating to music or using built-in programs, including sound sensitivity adjustment.
Managing LED display, self-test, display inversion, unit hours, software version, and reset.
Using the UC IR or Airstream IR remote/app for fixture control.
Details on specific functions controlled by the remote, like Standby, Full On, Strobe, and Color.
Describes functions controlled by channel 1 and 2 in 2-channel DMX mode.
Details functions controlled by channels 1 through 9 in 9-channel DMX mode.
Continues the explanation of functions for channels 6-9 in 9-channel DMX mode.
Procedures for replacing the fuse and cleaning the fixture for optimal performance.
Solutions for problems like no light output or unit not responding to sound.
Details on unpacking, intro, customer support, general instructions, and features.
Critical warnings regarding electrical shock, fire, eye damage, and unit handling.
Avoid shock/fire risks, ensure ventilation, indoor use, and proper mounting.
Unit requires qualified service; avoid damage, spills, and abnormal operations.
Details risks of laser radiation, potential eye injury, and the importance of not opening the housing.
Do not point lasers at people/animals, avoid direct eye exposure, and use safe setup practices.
Automatic voltage switch and explanation of DMX-512 for lighting control.
Connecting DMX fixtures, setting addresses, and data cable specifications.
Importance of using a terminator on the last unit in a DMX chain to avoid erratic behavior.
Secure mounting with clamps, structure support, and use of safety cables.
Equipment must be installed by a professional in a safe, out-of-reach location.
How to navigate the menu, set DMX address, and understand basic operations.
Configuration for DMX channel, show, UV speed, sound active, and master/slave modes.
Display inversion, LED control, self-test, fixture hours, software version, and reset.
Using a DMX controller for patterns, rotation, and strobing effects.
Operating to music or using built-in programs, including sound sensitivity adjustment.
Managing LED display, self-test, display inversion, unit hours, software version, and reset.
Using the UC IR or Airstream IR remote/app for fixture control.
Details on specific functions controlled by the remote, like Standby, Full On, Strobe, and Color.
Describes functions controlled by channel 1 and 2 in 2-channel DMX mode.
Details functions controlled by channels 1 through 9 in 9-channel DMX mode.
Continues the explanation of functions for channels 6-9 in 9-channel DMX mode.
Procedures for replacing the fuse and cleaning the fixture for optimal performance.
Solutions for problems like no light output or unit not responding to sound.
General| Control type | Buttons |
|---|---|
| Display type | LED |
| Product type | Disco spotlight |
| Product color | Black |
| Suitable for indoor use | Yes |
| Power source | AC |
| Input voltage | 100 - 240 V |
| Input frequency | 50 - 60 Hz |
| Power consumption (typical) | 70 W |
| Bulb power | 5 W |
| Light color | Green, Pink, Red, White |
| Bulb lifetime | 50000 h |
| Lamps quantity | 6 lamp(s) |
| Dimming range | 0 - 100 % |
| Lighting modes | DMX, Sound activated |
| DMX channels quantity | 2 channels |
| Lighting control protocols | DMX |
| Quantity | 1 |
Weight and Dimensions| Depth | 304 mm |
|---|---|
| Width | 230.5 mm |
| Height | 248 mm |
| Ball diameter | - \ |
To Next Page
