Why Advance acoustic Scrubber has On-board Battery charger fault?
If your Advance acoustic Scrubber is experiencing an on-board battery charger fault, it means an error has been generated via the serial communications between the charger and the A1 Control Board. This is due to an incorrect charging profile code being repeatedly sent by the charger, or the bit timing being severely out of spec. Check the charger's communication settings.
What to do if my Advance acoustic Floor Machine has no solution flow?
If there is inadequate or no solution flow, first check if the solution tank is empty and fill it if necessary. Next, inspect the solution lines, valves, or filter for clogs; flush the lines and clean the solution filter. Also, verify that the Solution Shutoff Valve is open. Finally, check the Solution Solenoid Valve and clean or replace it if needed.
How to improve the scrubbing performance of my Advance acoustic Floor Machine?
To improve scrubbing performance, start by checking the brush or pad for wear and replace if necessary. Ensure you are using the correct brush or pad type. Moving the machine too fast can reduce performance, so slow down. Insufficient solution flow can also be a factor, so increase the solution flow.
What to do if my Advance acoustic Floor Machine does not turn on?
If the machine does not power on, first check whether the Machine Battery Connector is disconnected and reconnect it. If that's not the issue, see if the 5 Amp circuit breaker has tripped and reset it after checking for a short circuit.
How to fix no detergent flow in my Advance acoustic Floor Machine?
If there is no detergent flow, ensure that the detergent container is filled. Check for any blockages or kinks in the detergent flow line; purge the system and straighten any kinked lines. Also, check the detergent pump, its wiring, and the connected lines.
What to do if Advance acoustic Scrubber has Scrub Deck Actuator position fault?
If your Advance acoustic Scrubber shows Scrub Deck Actuator position fault, the measured current was greater or equal to the minimum threshold value while the deck was moving, but the software timed out looking for the new position. Check the actuator for proper function and position feedback.
How to fix Brush Contactor (K2) coil open in Advance acoustic SC1500 Scrubber?
If the Brush Contactor of your Advance acoustic Scrubber is open, it indicates that the measured current was below the minimum value while the Brush Contactor should have been on. Inspect the Brush Contactor circuit for issues.
How to troubleshoot Vacuum Contactor (SSR1) coil open in Advance acoustic Scrubber?
If the Vacuum Contactor of your Advance acoustic Scrubber is open, it means the measured current was below the minimum value while the Vacuum Contactor should have been on. Check the Vacuum Contactor wiring.
How to fix Detergent Pump driver stuck on in Advance acoustic SC1500 Scrubber?
If the Detergent Pump driver of your Advance acoustic Scrubber is stuck on, it means the measured current was above the minimum value even when the Detergent Pump driver should have been off. Check the Detergent Pump driver for faults.
What to do if Advance acoustic Scrubber shows Scrub Deck Actuator overload?
If the Scrub Deck Actuator of your Advance acoustic Scrubber is overloaded, it means it has drawn more than 4.5 amps. Try reducing the load on the Scrub Deck Actuator or look for any blockages.
Key safety guidelines for operating the machine.
Specific safety warnings related to battery handling and charging.
Detailed explanations of each control and indicator on the panel.
Step-by-step guide for installing batteries into the machine.
Steps to install the disc brush onto the pad holder.
Procedure for mixing detergent and filling the solution tank.
Steps to program strong and weak detergent ratios.
Detailed steps for operating the machine to scrub floors.
Adjusting scrub pressure, solution flow, and vacuum level.
Procedures for emptying and cleaning tanks and squeegees.
Daily checks and cleaning required for the machine.
How the electromagnetic brake operates and engages.
Steps for charging batteries using the onboard charger.
Steps for charging batteries using an external charger.
Weekly procedure for checking battery water levels.
Critical warnings regarding VRLA battery charging and warranty.
Procedure for charging VRLA batteries with an onboard charger.
Procedure for charging VRLA batteries with an external charger.
Instructions for inspecting, reversing, or replacing squeegee blades.
General| Brand | Advance acoustic |
|---|---|
| Model | SC1500 |
| Category | Scrubber |
| Language | English |
To Next Page
