Advance acoustic SC900 ST-28D

Questions and Answers

M
Michaela StewartJul 31, 2025
What to do if my Advance acoustic Scrubber has poor water pick-up?
- S
  Samantha LarsenJul 31, 2025
  If the Advance acoustic Scrubber isn't picking up water effectively, there are several potential causes. The squeegee blades might be worn or torn, in which case you should reverse or replace them. The squeegee might be out of adjustment; adjust it so the blades touch the floor evenly. The recovery tank could be full, so empty it. Check for leaks in the recovery tank drain hose or cover gasket, and secure the drain hose cap or replace the hose or gasket if needed. Debris might be caught in the squeegee; clean the squeegee tool. The vacuum hose could be clogged; remove any debris. You might be using too much solution; adjust the solution flow at the control panel. Finally, the debris catch cage could be full; empty it.
S
stricklandbarbaraAug 4, 2025
Why is the scrubbing performance of my Advance acoustic Scrubber poor?
- C
  Carla WilliamsonAug 4, 2025
  If your Advance acoustic Scrubber's scrubbing performance is poor, the brush or pad might be worn, so rotate or replace the brushes. You might be using the wrong brush or pad type or the wrong cleaning chemical; consult Advance. You might be moving the machine too fast; slow down. You might not be using enough solution; increase the solution flow at the control panel.
M
Matthew BrightAug 8, 2025
How to fix inadequate solution flow in Advance acoustic Scrubber?
- W
  williamlopezAug 9, 2025
  If there is inadequate or no solution flow in your Advance acoustic Scrubber, first check if the solution tank is empty and fill it if necessary. The solution lines, valves, filter, or trough might be clogged; flush the lines and trough, and clean the solution filter. Ensure the solution shutoff valve is open. Finally, the solution solenoid valve may need cleaning or replacement.
P
Paula RobertsAug 12, 2025
What to do if my Advance acoustic Scrubber does not run?
- D
  David TaylorAug 12, 2025
  If your Advance acoustic Scrubber is not running, check whether the battery connector is disconnected and reconnect it if necessary. Also, check for a tripped 2.5 Amp circuit breaker; look for an electrical short circuit and reset the breaker.
K
Kathy WebbAug 17, 2025
Why is there no FWD/REV wheel drive in my Advance acoustic Scrubber?
- Z
  Zachary HahnAug 17, 2025
  If there is no forward or reverse wheel drive on your Advance acoustic Scrubber, check the drive system speed controller for error fault codes. Also, check for a tripped 30 Amp circuit breaker and look for a drive motor overload.
J
Jonathan GreenAug 21, 2025
How to improve poor sweeping performance on Advance acoustic Scrubber?
- M
  mikayla41Aug 21, 2025
  If your Advance acoustic Scrubber (Cylindrical System) exhibits poor sweeping performance, start by emptying and cleaning the hopper, as it may be full. If the hopper isn't the issue, inspect the brushes for wear and replace them if needed. Additionally, if the bristles have taken a set, rotate the brushes to improve performance.
S
Stephen BradfordAug 26, 2025
What to do if there is no detergent flow in Advance acoustic Scrubber?
- A
  Anna SanchezAug 26, 2025
  If there is no detergent flow in your Advance acoustic Scrubber (EcoFlex models only), first check if the detergent cartridge is empty and fill it if necessary. Inspect the detergent flow line for plugs or kinks; purge the system and straighten any kinks. Ensure the dry seal cap on the detergent cartridge is sealed correctly; reseat it if necessary. Finally, check the detergent pump wiring; connect or reconnect it if disconnected or backwards.