View the expanded manual:
http://aeotec.com/support
WallMote.
Aeotec WallMote is an intelligent Z-Wave remote controller that
mounted on a wall. It has 2 touch buttons that you can easily control
the Z-Wave devices in your home network via touching, long pressing
or sliding the button areas.
Its surface has a RGB LED to indicate the button actions also
accompanied by touch beep and vibration.
The WallMote is also a security Z-Wave device and supports Over The
Air (OTA) feature for the products rmware upgrade.
Familiarize yourself with your WallMote.
Quick start.
Advanced.
1.
2.
Installing your WallMote.
Adding your WallMote to your Z-Wave network.
Attach your WallMote to its Back Mounting plate.
Send a wake up notification.
Removing your WallMote from a Z-Wave network.
Security or Non-security feature of your WallMote in Z-wave
network.
Advanced Parameter Configurations.
1.
2.
3.
4.
Let your Z-Wave primary controller/gateway enter into pairing/
inclusion mode.
Take your WallMote near to your primary controller.
Press the Action Button once on your WallMote, the LED will blink
with green color.
If your WallMote has been successfully added to your Z-Wave
network, its green LED will be solid for 2 seconds and then off. If
the adding was unsuccessful and the red LED will be solid for 2
seconds and then off, repeat the above steps.
With your WallMote added to the Z-Wave network. It’s now time to
insert the main unit into the corresponding Back Mount plate.
Put the main unit in the top-left direction on the Back Mounting, and
then push the WallMote into the Back Mounting Plate, the WallMote
will be attracted by the magnets on the Back Mount plate, as the
gure below shows.
With your WallMote now working as a part of your smart home, you’ll
be able to configure it from your home control software or phone
application. Please refer to your software’s user guide for precise
instructions on conguring the WallMote to your needs.
With your mounting plates prepared to hold each component of your
WallMote, it’s time to add it to your Z-Wave network.
In order to send your WallMote new conguration commands from
your Z-Wave controller or gateway, it will need to be woken up.
Remove your WallMote unit from its Back Mounting Plate, press and
hold the Action Button for 3 seconds(the buzzer chirp once and the
orange LED will be ON) on the back of the WallMote unit and then
release it. This will trigger and send a wake up notication command
to your controller/gateway, then your WallMote will wake up for 10
minutes and the orange LED will fast blink while it is awake (if the
WallMote does not receive the Wake Up No More Info from the
primary Controller).
Your WallMote can be removed from your Z-Wave network at any
time. You'll need to use your Z-Wave network's main controller/
gateway. To do this, please refer to the part of their respective
manuals that tell you how to remove devices from your network.
1.
2.
3.
4.
Put your primary controller into device removal mode.
Unlock your WallMote from the Back Mount plate and take the
WallMote unit near to your primary controller.
Press the Action Button on your WallMote.
If your WallMote is successfully removed from the Z-Wave network,
the LED will become a colourful gradient for a few seconds and
then turn off. If the removing was unsuccessful, the red LED will be
solid for 2 seconds and then turn off, repeat the above steps.
Not all gateways will allow you to further configure your Z-Wave
devices, but in the case that your gateway does allow it, the WallMote
has some available parameter configurations that will allow you to
congure it further to your liking.
Touch beep
This will enable or disable the sound effects when you press or touch
the sensing area. By default, this is enabled.
Parameter 1 [1 byte]
0: Disable
1: Enable
Note: You can also enable or disable the sound effects via pressing
and holding the Action Button for 12 seconds (the buzzer chirp once
and the red LED will fast blink) and then release.
Including WallMote as a non-secure device:
If you want your WallMote as a non-security device in your Z-wave
network, you just need to press the Action Button once on WallMote
when you use a controller/gateway to add/include it. The green LED
will be on for 2 seconds and then the orange LED will fast blink for
10 minutes (if the WallMote does not receive the Wake Up No More
Info command from primary Controller) to indicate the inclusion is
successful.
Including WallMote as a secure device:
In order to take full advantage of all functionality the WallMote, you
Selecting a place or wall in your home to afx your WallMote’s Back
Mount plate.
Using the Double-sided tap, wipe the two surfaces clean of any oil
or dust with a damp towel. When the surface has completely dried,
peel one side of the tape back and attach it to the corresponding
section on the rear side of the Back Mounting Plate.
WallMote
1
2
3
4
IMPORTANT!
This product has been fully tested and certied to work
with Z-Wave by the Z-Wave Alliance. It is crafted using
Z-Wave Plus, the latest device version of Z-Wave.
As such, if the product does not work with your
gateway, please be sure to check with your gateway
manufacturer that they have integrated this device with
their gateway for full operation.
1.
2.
3.
4.
WallMote
Back-Mount plate
Double-Sided tape
Micro USB cable
①
®
②
③
④
RGB LED
Button 1
Button 2
Magnet
Magnet
Micro USB port
Action Button
Main unit (Front)
Main unit (Back)
Back-Mount plate
Magnet
may want your WallMote is a security device that uses secure/
encrypted message to communicate in Z-wave network, so a security
enabled controller/gateway is needed for the WallMote to be used as
a security device. You need to press the WallMote’s Action Button 2
times within 1 second when your security controller/gateway starts
the network inclusion. The blue LED will be on for 2 seconds and then
the orange LED will fast blink for 10 minutes (if the WallMote does not
receive the Wake Up No More Info command from primary Controller)
to indicate the inclusion is successful.
Note: When the WallMote is placed on somewhere, keep the glass
button surface upward direction and no other physical surface or
desktop contact with the glass button surface to avoid false triggering
and battery consumption.
To Next Page
Need help?
General
