AGI GRAINMAXX 6300 Series

Other manuals for AGI GRAINMAXX 6300 Series

Questions and Answers

S
Susan BenjaminAug 13, 2025
What to do if AGI Tools have poor product flow?
- L
  Lisa RichardsonAug 13, 2025
  If you're experiencing poor product flow with your AGI Tools, consider these potential causes and solutions: The input speed might be too slow, in which case you should increase the engine rpm. There might be inadequate material flow from the truck or hopper, so you should increase the flow of material. If the flow into the hopper is restricted, clear the grating of obstructions. Note that unloading rates are designed for dry grain; if the material is too wet or heavy, this could be the cause. Finally, inspect the flighting for wear and repair or replace as needed.
T
Teresa JeffersonAug 17, 2025
Why the flighting does not turn in AGI Tools?
- T
  Tony HuntAug 17, 2025
  If the flighting in your AGI Tools isn't turning, several issues could be the cause. First, the auger flighting might be plugged or obstructed; identify and remove any obstructions. Second, the coupler bolt below the non-rotating section could be broken or missing; replace the bolt. A seized bearing can also prevent turning; identify the bearing and replace it. A broken chain will also stop the flighting; identify the chain and repair or replace it. If the gearbox is seized, fix or replace the gearbox. Also, check the gearbox coupler bolt; if it is broken or missing, replace it. Lastly, a failed PTO shear bolt can cause this issue, so replace both PTO shear bolts.
B
Brandon HarrisAug 21, 2025
What to do if the auger lifts slowly in AGI Tools?
- A
  Anthony BowmanAug 21, 2025
  If your AGI Tools auger is lifting slowly, it could be due to inadequate hydraulic pressure from the source. Consider using an alternate hydraulic pressure source and contact your local dealer for assistance. Also, if the auger lowers faster than it lifts, the check valve may be installed in the opposite direction. Lower the auger to the transport position and inspect the check valve; reinstall it in the opposite direction if required, following the indicator arrow on the valve.
T
Tiffany SandersAug 25, 2025
How to fix noisy auger flighting in AGI Tools?
- B
  Briana BrownAug 25, 2025
  If the auger flighting in your AGI Tools is noisy, it's likely due to an obstruction in the auger tube. Identify and remove the obstruction to resolve the noise.
E
Edward SparksAug 28, 2025
What to do if scissor lift is not lifting auger in AGI Tools?
- M
  Ms. Renee FitzgeraldAug 28, 2025
  If the scissor lift isn't lifting the auger in your AGI Tools, check if the ball valve on the lift line is closed. If so, open the ball valve. If that's not the issue, there might be inadequate pressure from the source. Try using an alternate hydraulic pressure source and contact your local dealer for assistance.
R
rogersreginaSep 1, 2025
What to do if the auger will not stay elevated in AGI Tools?
- S
  Sandra ReeseSep 1, 2025
  If the auger in your AGI Tools won't stay elevated, first ensure that the ball valve is closed while in the elevated position. If it still won't stay up, there may be a leaking hydraulic hose or fitting; lower the auger to the transport position and repair leaks as required. Finally, a leaking seal in the hydraulic cylinder could be the cause; lower the auger to the transport position and repair or replace the winch.
T
Terri MartinezSep 4, 2025
Why the auger makes noise while lifting in AGI Tools?
- M
  monique73Sep 4, 2025
  If your AGI Tools auger makes noise while lifting, it's likely that frame parts are loose and moving. Replace any damaged components and re-tension the frame fasteners.
S
Stacey BlankenshipSep 8, 2025
What to do if the lift cylinder discharges oil from breather while lifting AGI Tools?
- T
  Tony StevensSep 8, 2025
  If the lift cylinder in your AGI Tools discharges oil from the breather while lifting and the auger still lifts, this is likely just captured oil in the top of the cylinder. Clean up the oil spill and continue operation as normal. However, if the auger will not lift, the seal in the hydraulic cylinder is damaged. Lower the auger to the transport position and repair the hydraulic cylinder as required.