To Next PageTo Next PageWhat to do if blade tips of bottom knife work into blades of top knife of Agria Lawn Mower?
If the blade tips of the bottom knife are working into the blades of the top knife on your Agria Lawn Mower, it indicates that the top knife protrudes too far over the bottom knife. Adjust the knife holders and guide pieces to correct this.
How to fix Agria 3600 BM Lawn Mower when the engine does not start?
If your Agria Lawn Mower engine isn't starting, there are several potential causes. First, ensure the choke is pulled. Next, verify that the safety circuit is set to the start position. If there's too much fuel in the engine, dry and adjust the spark plug and try starting at full throttle. Also, check the engine-off-line and its connections. Finally, inspect for air leaks due to a loose carburetor and tighten the attachment bolts and suction line if needed.
Why is my Agria 3600 BM Lawn Mower misfiring?
Misfiring in your Agria Lawn Mower could stem from several reasons. Check if the engine is running in CHOKE range and set the CHOKE-lever appropriately. Ensure the spark plug connector is firmly connected to the spark plug and fix the ignition cable retaining device. A clogged fuel line or poor fuel quality can also cause misfires, so clean the fuel line and fill with fresh fuel. Additionally, a clogged vent opening in the fuel tank cap may be the culprit, requiring you to exchange the fuel tank cap. Finally, drain the fuel and fill it with fresh fuel to eliminate any water or dirt in the fuel system.
What to do if Agria 3600 BM engine does not stop?
If your Agria Lawn Mower engine won't stop when set to stop, it could be due to a defective engine-stop-line or a missing earth connection; check the line, connection, and earth contact. Another potential cause is damaged sealing, which would require exchanging the sealing. Poor compression can also cause this issue; it is recommended to have the engine checked.
Why is the clutch slipping on my Agria 3600 BM?
Clutch slippage in your Agria Lawn Mower can occur if the hand clutch lever is misadjusted; adjust the clutch free play to correct this. Alternatively, the clutch disc may be worn out and require replacement.
Why Agria Lawn Mower blades are not on top of each other?
If the blades of your Agria Lawn Mower are not on top of each other, it may be due to bent blades or knives, or a twisted knife back. Check whether the knives are straight and re-align if necessary.
Explains various warning and informational symbols used in the manual.
Details recommended lubricants and protective agents for the machine.
Specifies suitable fuel types for the engine.
General advice on maintenance and professional repair services.
Diagram illustrating components of the power mower.
Diagram illustrating components of the power mower.
Detailed list of parts for Figure A diagram.
Detailed list of parts for Figure B diagram.
Core safety rules and accident prevention guidelines.
Defines intended use, limitations, and manufacturer liability.
Safety considerations for the operating environment.
Focuses on safe operation and key safety devices.
Safety precautions when fitting and using implements.
Specific safety notes for the mowing attachment.
Procedures for safe shutdown and securing the machine.
Guidance on the safe use of weights.
Safety measures for snow clearing operations.
Safety precautions during maintenance activities.
Safety guidelines for storing the machine.
Critical safety information for fuel, oil, and engine handling.
Safety related to tire maintenance and pressure.
Safety considerations for electrical components.
Interpretation and understanding of all warning symbols.
Provides key physical dimensions of the machine.
Details different track width configurations.
Technical details of the mowing drive system.
Specifications for transmission oil.
Performance data on forward and reverse speeds.
Description of the steering handle features.
Information on vibration levels experienced by the operator.
Comprehensive technical specifications for the engine.
Guidelines for safe operation on inclines.
Data on noise emissions from the machine.
Overview of the engine and its operation.
Details on ignition system and break-in period.
Information on the fan-cooled system and cleaning.
Function and maintenance of the air filter.
Description of the lever for engine speed adjustment.
Explanation of the safety lever and its function.
Details on the double disc dry clutch operation and locking.
Description of the mechanical gearbox and gear changing.
Information on the PTO-driven mowing drive.
Instructions for engaging and disengaging the mowing drive.
General information about the steering handle.
Procedure for adjusting the handle height.
Steps for attaching implements to the machine.
Steps for detaching implements from the machine.
Description of the quick attachment coupling point.
Lists available cutter bar options.
Instructions for mounting cutter bars.
Specific assembly steps for certain cutter bars.
Specific fitting details for universal cutter bars.
Specific fitting details for municipal cutter bars.
Specific assembly steps for the finger cutter bar.
Procedure for removing and replacing mowing knives.
Instructions for installing new mowing knives.
Instructions for fitting drive wheels for optimal traction.
Guidelines for using snow chains.
Procedure for installing twin wheels.
Instructions for fitting strake wheels.
Initial setup procedures, including engine break-in.
Pre-operation checks for fuel, oil, and general condition.
Step-by-step guide for starting the petrol engine.
Specific instructions for starting the petrol engine.
Procedure for safely shutting down the engine.
Specific instructions for shutting down the petrol engine.
Instructions for performing mowing operations.
Steps to change direction from forward to reverse.
Steps to change direction from reverse to forward.
Important notes regarding mowing and cleaning.
Procedure for starting the engine on inclined surfaces.
Adjustment procedure for the cutter bar's running bases.
Maintenance tasks related to the engine.
Instructions for checking the engine oil level.
Procedure for draining and refilling engine oil.
Cleaning and maintenance procedures for the air filter.
Steps for cleaning the engine's cooling system.
Inspection and cleaning of the exhaust system.
Spark plug maintenance and gap adjustment.
Guidelines for exchanging fuel hoses.
Procedure for cleaning the fuel strainer.
Instructions for cleaning the cylinder head.
Procedure for adjusting valve lash.
How to correctly adjust and maintain engine idling speed.
Information regarding the governor's function and adjustment.
General maintenance for the machine.
Maintenance procedures for the gearbox.
Maintenance for drive wheels, including bolt tightening.
Lubrication of coupling points and PTO shaft.
How to check and adjust clutch play.
Checking the proper function of the safety circuit.
Maintenance specific to the mowing drive.
How to check the oil level in the mowing drive.
Procedure for changing the oil in the mowing drive.
Procedure for adjusting the knife driver play.
Maintenance related to the mowing attachment.
Specific maintenance for the universal cutter bar.
How to adjust knife holders and guide pieces.
Specific maintenance for the finger cutter bar.
Procedure for adjusting knife guiding devices.
Detailed steps for correct adjustment of the finger cutter bar.
Specific maintenance for the municipal cutter bar.
Maintenance and adjustment of pivot arm guides.
Instructions for sharpening and grinding mowing knives.
General upkeep and checks for the machine.
Cleaning instructions for the engine.
General cleaning procedures.
Cleaning the cutter bar after use.
Cleaning and lubricating the mowing drive and machine.
Procedures for preparing the machine for long-term storage.
Cleaning steps before storage.
Steps to preserve the engine during storage.
Recommendations for drive wheel storage.
Clutch handling during storage.
Advice on suitable storage locations.
Methods for protecting the machine during storage.
Common causes and solutions for engine starting failure.
Troubleshooting engine misfires.
Diagnosing and resolving engine overheating issues.
Troubleshooting misfires occurring at high engine speeds.
Solutions for the engine stalling during idle operation.
Addressing issues causing the engine to run rough.
Troubleshooting the engine failing to shut down.
Identifying causes for reduced engine power.
Resolving problems with the clutch not disengaging.
Troubleshooting clutch slippage issues.
Identifying and fixing sources of excessive vibration.
Diagnosing sudden drops in mowing performance.
Solutions for when plant material obstructs the knives.
Adjusting blades to prevent interference.
Correcting blade alignment issues.
A list of recommended lubricants and anti-corrosive agents.
Information on adhesives and sealing compounds.
Available spray varnish colors.
List of common parts subject to wear.
References for ordering spare parts.
Specific details about the engine model.
Diagram of engine components with labels.
Diagram of engine components with labels.
Specific details about the engine model.
Diagram of engine components with labels.
Diagram of engine components with labels.
Illustrates the engine's connection within the electrical circuit.
Depicts the magnet ignition system's wiring.
Shows the safety lever switch integration.
General| Category | Lawn Mower |
|---|---|
| Type | Ride-on |
| Engine Type | Petrol |
| Engine | Briggs & Stratton |
| Grass Collector Capacity | 300 L |
