Need help?Do you have a question about the Aim MXS STRADA and is the answer not in the manual?
Defines the MXS Strada as a color, high-contrast, 5" TFT dash for race and street use.
Explains data sources including ECU, analog/digital inputs, GPS, and expansions.
Discusses the ability to choose page styles and configure data display.
Details how alarm LEDs can be configured by color and blinking frequency.
States that up to eight fully customizable pages can be defined.
Provides a visual overview and labeling of the MXS Strada dash components.
Details the 10 RGB gear flash LEDs and 6 alarm LEDs with configuration options.
Explains how MXS Strada samples data from vehicle ECUs using CAN, RS232, or K Line.
Lists ways to acquire RPM: from ECU, square wave signal, or coil.
Describes reading RPM directly from the vehicle's ECU data stream.
Details connecting RPM via a 5-50V square wave or low voltage coil signal.
Outlines three sources for speed: ECU, GPS receiver, or speed channel.
Explains reading vehicle speed directly from the ECU's data stream.
Details obtaining vehicle speed using the optional GPS08 receiver.
Describes using a dedicated speed input for wheel sensor signals.
Describes the 4 analog inputs sampled up to 1000 Hz, for various sensors.
Details the single 1 Amp digital output and its configuration for events.
Introduces RaceStudio3 for configuration, analysis, and device management.
Explains the configuration page structure for organizing and creating settings.
Configures input channels, speed, and RPM parameters within RaceStudio3.
Selects the vehicle ECU and manages data stream frequency and channel names.
Sets up CAN2 stream for non-engine control units like ABS or suspension.
Sets lap detection parameters, track width, and beacon settings.
Configures alarm LEDs, messages, and digital outputs for events.
Customizes display pages, layouts, channel labels, units, and scale.
Configures CAN output messages to transmit data on the vehicle network.
Manages configurations by modifying, exporting, or deleting existing settings.
Allows viewing live data and calibrating channels through RaceStudio3.
Enables recalling best laps, max/min speed, and RPM after tests.
Introduces expansion modules like Lambda controllers, TC Hub, and GPS for enhanced performance.
Details the pin assignments for the 23-pin AMP and 14-pin connectors.
Provides dimensions, display specs, connectivity, weight, and power consumption.
Defines the MXS Strada as a color, high-contrast, 5" TFT dash for race and street use.
Explains data sources including ECU, analog/digital inputs, GPS, and expansions.
Discusses the ability to choose page styles and configure data display.
Details how alarm LEDs can be configured by color and blinking frequency.
States that up to eight fully customizable pages can be defined.
Provides a visual overview and labeling of the MXS Strada dash components.
Details the 10 RGB gear flash LEDs and 6 alarm LEDs with configuration options.
Explains how MXS Strada samples data from vehicle ECUs using CAN, RS232, or K Line.
Lists ways to acquire RPM: from ECU, square wave signal, or coil.
Describes reading RPM directly from the vehicle's ECU data stream.
Details connecting RPM via a 5-50V square wave or low voltage coil signal.
Outlines three sources for speed: ECU, GPS receiver, or speed channel.
Explains reading vehicle speed directly from the ECU's data stream.
Details obtaining vehicle speed using the optional GPS08 receiver.
Describes using a dedicated speed input for wheel sensor signals.
Describes the 4 analog inputs sampled up to 1000 Hz, for various sensors.
Details the single 1 Amp digital output and its configuration for events.
Introduces RaceStudio3 for configuration, analysis, and device management.
Explains the configuration page structure for organizing and creating settings.
Configures input channels, speed, and RPM parameters within RaceStudio3.
Selects the vehicle ECU and manages data stream frequency and channel names.
Sets up CAN2 stream for non-engine control units like ABS or suspension.
Sets lap detection parameters, track width, and beacon settings.
Configures alarm LEDs, messages, and digital outputs for events.
Customizes display pages, layouts, channel labels, units, and scale.
Configures CAN output messages to transmit data on the vehicle network.
Manages configurations by modifying, exporting, or deleting existing settings.
Allows viewing live data and calibrating channels through RaceStudio3.
Enables recalling best laps, max/min speed, and RPM after tests.
Introduces expansion modules like Lambda controllers, TC Hub, and GPS for enhanced performance.
Details the pin assignments for the 23-pin AMP and 14-pin connectors.
Provides dimensions, display specs, connectivity, weight, and power consumption.
General| Brand | Aim |
|---|---|
| Model | MXS STRADA |
| Category | Heart Rate Monitor |
| Language | English |
To Next Page
