Aiphone JB-2MED - Page 19

- 19 -
2. If the absence set (auto absence recording) is operating, the SET
button flashes to show that there has been a caller (if the image is
played, it goes back to being lit). When the image is played, the
number of callers who came while you were out is displayed.
Example: "2/5" means Second image from a total of 5.
3.
Press the SET button again to cancel. The SET button light will go off.
1. In step 1, if pressed and held for more than 2 sec., it will enter
setting mode.
NOTES: Cancellation in step 3 is not possible while the SET button is
flashing. First play the recorded screen.
Nederlands
7-11
Automatic updating function for recorded screens
If the number of recorded pictures exceeds the maximum number set
for recording mode, the oldest picture is automatically replaced with
the new picture (pictures are erased even if they have not been played).
[1] Adding new picture
[2] Number of pictures set for recording mode
[3] Erasing the earliest taken picture
NOTES: You can save pictures that you want to keep. (P22)
Automatic updating function for recorded screens
If the number of recorded pictures exceeds the maximum number set
for recording mode, the oldest picture is automatically replaced with
the new picture (pictures are erased even if they have not been played).
[1] Adding new picture
[2] Number of pictures set for recording mode
[3] Erasing the earliest taken picture
NOTES: You can save pictures that you want to keep. (P22)
Automatic updating function for recorded screens
If the number of recorded pictures exceeds the maximum number set
for recording mode, the oldest picture is automatically replaced with
the new picture (pictures are erased even if they have not been played).
[1] Adding new picture
[2] Number of pictures set for recording mode
[3] Erasing the earliest taken picture
NOTES: You can save pictures that you want to keep. (P22)
Automatic updating function for recorded screens
If the number of recorded pictures exceeds the maximum number set
for recording mode, the oldest picture is automatically replaced with
the new picture (pictures are erased even if they have not been played).
[1] Adding new picture
[2] Number of pictures set for recording mode
[3] Erasing the earliest taken picture
NOTES: You can save pictures that you want to keep. (P22)
English
Français
Deutsch
Español
Nederlands
7-12
Play
1. Press the PLAY button to view the newest picture.
2. Each time the PLAY button is pressed, it moves to the next picture
that was previously recorded. After the final picture, it becomes a
blue screen before returning to the first picture. Press the REC
button to reverse the selection direction.
3. Press the TALK button to end. It ends automatically approx. 1 min.
after the final operation.
1.
In step 1, playback is not possible if there are no recorded pictures.
2. In 16-picture/4-frame mode, the REC button in step 2 is used
to view each picture in a full-screen view.
Play
1. Press the PLAY button to view the newest picture.
2. Each time the PLAY button is pressed, it moves to the next picture
that was previously recorded. After the final picture, it becomes a
blue screen before returning to the first picture. Press the REC
button to reverse the selection direction.
3. Press the TALK button to end. It ends automatically approx. 1 min.
after the final operation.
1.
In step 1, playback is not possible if there are no recorded pictures.
2. In 16-picture/4-frame mode, the REC button in step 2 is used
to view each picture in a full-screen view.
Play
1. Press the PLAY button to view the newest picture.
2. Each time the PLAY button is pressed, it moves to the next picture
that was previously recorded. After the final picture, it becomes a
blue screen before returning to the first picture. Press the REC
button to reverse the selection direction.
3. Press the TALK button to end. It ends automatically approx. 1 min.
after the final operation.
1.
In step 1, playback is not possible if there are no recorded pictures.
2. In 16-picture/4-frame mode, the REC button in step 2 is used
to view each picture in a full-screen view.
English
Absence set (Auto absence recording)
1. If the SET button is pressed once (less than 2 sec.), it will light and
the unit will be set.
2. If the absence set (auto absence recording) is operating, the SET
button flashes to show that there has been a caller (if the image is
played, it goes back to being lit). When the image is played, the
number of callers who came while you were out is displayed.
Example: "2/5" means Second image from a total of 5.
3.
Press the SET button again to cancel. The SET button light will go off.
1. In step 1, if pressed and held for more than 2 sec., it will enter
setting mode.
NOTES: Cancellation in step 3 is not possible while the SET button is
flashing. First play the recorded screen.
Automatic updating function for recorded screens
If the number of recorded pictures exceeds the maximum number set
for recording mode, the oldest picture is automatically replaced with
the new picture (pictures are erased even if they have not been played).
[1] Adding new picture
[2] Number of pictures set for recording mode
[3] Erasing the earliest taken picture
NOTES: You can save pictures that you want to keep. (P22)
Français
Deutsch
29/MAR/04 20:03
30/MAR/04 09:48
30/MAR/04 20:25
01/APR/04 15:30
01/APR/04 17:15
[1] [2] [3]
JB-2MED
01/APR/04 14:30
16-picture, 4-frame mode
16/32/60-picture mode
J
B
-2
M
E
D
TALK
C
AL
L
M
O
N
I
T
O
R
R
EC
P
LA
Y
SE
T
J
B
-
2
M
E
D
TAL K
C
A
L
L
M
O
N
IT
O
R
R
E
C
P
L
A
Y
S
E
T
PLAY
REC
1
2
3
01/APR/04 14:30 01/APR/04 13:25 01/APR/04 10:18
01/APR/04 14:30
JB-2MED