EasyManua.ls Logo

AirMan SDG60S-3A2 - User Manual

AirMan SDG60S-3A2
76 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
www.AirmanArizona.com
REQUEST PARTS ON LINE
www.AirmanArizona.com
REQUEST PARTS ON LINE

Table of Contents

Questions and Answers

  • K
    kellerstephanieAug 9, 2025
    What to do if the engine oil pressure warning lamp turns on in my AirMan SDG60S-3A2?
    • C
      Candace CarterAug 9, 2025
      If the engine oil pressure warning lamp illuminates, it could be due to several reasons. First, check if there is an engine oil shortage and replenish the oil if needed. Other potential causes include a clogged engine oil filter (change it), a malfunctioning oil pressure switch (replace it), or loosened/disconnected wiring or connectors (check and fasten them).
  • T
    tsilvaAug 16, 2025
    Why does the over crank warning lamp go on in my AirMan Inverter?
    • S
      Sean WashingtonAug 16, 2025
      The over crank warning lamp might activate due to several issues. It could be caused by a fuel filter clogging, in which case you should disassemble, clean, and change the filter. Another cause might be a filter clogging in the fuel air-bleeding electromagnetic pump (SDG45S/60S/75S), so change the filter. Also, a malfunctioning fuel cut off solenoid may be the reason, so replace the solenoid. The warning lamp can also indicate that there is no diesel fuel oil, so replenish the fuel. Finally, air mixing in fuel pipings may be the cause, so bleed the air.
  • R
    raymondmartinezAug 25, 2025
    How to fix a coolant temperature warning lamp that turns on in AirMan SDG60S-3A2 Inverter?
    • C
      Christina JonesAug 26, 2025
      If the coolant temperature warning lamp turns on, consider the following potential causes: 1. Radiator clogging (clean it). 2. Faulty thermostat (change it). 3. Faulty coolant temperature switch (change it). 4. Shortage of coolant (replenish it). 5. Slip of fan belt (adjust tension). 6. Looseness or disconnection of wiring or connectors (check and fasten).
  • R
    Robert RobinsonSep 1, 2025
    What causes the charge warning lamp to turn on in AirMan SDG60S-3A2?
    • J
      jenniferbryantSep 1, 2025
      The charge warning lamp turning on may indicate an alternator problem (check or change it), a slipping fan belt (fasten or change it), or looseness/disconnection of wiring or connectors (check and fasten them).

Summary

Safety Precautions

Caution Before Operation

Essential safety guidelines to follow before starting the generator operation.

Caution During Operation

Critical safety warnings and instructions for safe generator operation.

Caution During Inspection and Maintenance

Safety measures and precautions for performing inspection and maintenance tasks.

Names of Components

Unit Appearance and Part Names

Main Components Identification

Instrument Panel Layout

Warning and Emergency Display Functions

Explanation of warning lamps, their associated troubles, and troubleshooting measures.

Transportation

Safe Transportation Procedures

Guidelines for safely hoisting, securing, and transporting the generator unit.

Installation

Installation Site and Conditions

Recommended site requirements and environmental conditions for generator installation.

Cable Selection and Connection

Guidance on selecting appropriate cables and connecting loads to the generator.

Electrical Connection Types

Grounding Methods

Proper grounding procedures for the generator and connection to building electrical systems.

Operation

Pre-Operation Checks

Essential checks and inspections to perform before starting the generator.

Engine Oil Level Check

Coolant Level and Fuel Checks

Generator Unit Operation

General procedures and important notes for operating the generator unit.

Starting Procedures

Step-by-step instructions for starting the generator in manual and automatic modes.

Meter and Indicator Light Status

Stopping Procedures

Steps for safely shutting down the generator in manual operation mode.

Frequency Adjustment

Emergency Stop Functionality

How to use the emergency stop button and reset the system.

Periodic Inspection;Maintenance

Important Inspection and Maintenance Items

Key considerations and precautions for periodic inspection and maintenance tasks.

Daily Inspection and Operation Log

Procedures for daily inspections and maintaining an operation log for monitoring.

Component Inspection Locations

First Maintenance at 50 Hours

Specific maintenance tasks required at the initial 50-hour service interval.

Maintenance Every 250 Hours

Periodic Inspection Checklist

Maintenance;Adjustment

Battery Maintenance Procedures

Using Jumper Cables Safely

Troubleshooting Common Issues

Identifies common symptoms, causes, and countermeasures for generator problems.

Wiring Diagram

SDG25 S Generator Wiring Diagram

SDG45 S;60 S Generator Wiring Diagram

SDG75 S;100 S Generator Wiring Diagram

SDG25 S Engine Wiring Diagram

SDG45 S Engine Wiring Diagram

SDG60 S Engine Wiring Diagram

SDG75 S;100 S Engine Wiring Diagram

AirMan SDG60S-3A2 Specifications

General IconGeneral
BrandAirMan
ModelSDG60S-3A2
CategoryInverter
LanguageEnglish

Related product manuals