Airwell PNX 30 DCI - User Manual

Questions and Answers

W
William HendersonAug 19, 2025
What to do if the Airwell Heat Pump compressor is overheated?
- T
  Travis MorrisAug 19, 2025
  If the Airwell Heat Pump compressor is overheating and not producing capacity, possible causes include an EEV problem, refrigerant leakage, or a blockage in either the indoor or outdoor coil. You should check the EEV and refrigeration system. Also, clean the filters and remove any blockage from the indoor coil. Clear any obstructions from the outdoor coil and prevent air bypass.
W
whitakertammyAug 21, 2025
Why Airwell Heat Pump compressor operates but has no capacity?
- E
  Erica NolanAug 21, 2025
  If your Airwell Heat Pump compressor operates but there's no capacity, it could be due to an EEV problem, refrigerant leakage, or a blockage in the indoor or outdoor coil. You should check the EEV and refrigeration system. Clean the filters and remove any blockage from the indoor coil. Remove any blockages from the outdoor coil and prevent air bypass.
L
Lisa ClarkAug 23, 2025
What to do if there's water leakage from my Airwell Heat Pump indoor unit?
- C
  Courtney KellyAug 25, 2025
  If you notice water leakage from the indoor unit of your Airwell Heat Pump, it's likely that the drainage tube is blocked. To resolve this, check and open the drainage tube.
J
Jacob BonillaAug 26, 2025
Why does my Airwell Heat Pump compressor stop during operation?
- K
  Kelly GriffinAug 26, 2025
  If the Airwell Heat Pump compressor stops during operation, it could be due to electronic control issues or refrigerant leakage. You should check the diagnostics and the refrigeration system to identify the problem.
D
Daniel SmithAug 28, 2025
What causes my Airwell Heat Pump to stop suddenly?
- C
  Catherine LewisAug 28, 2025
  If the Airwell Heat Pump suddenly stops during operation, it could be due to EMC interference. You should check for EMC problems.
M
Matthew DavisAug 30, 2025
Why doesn't the indoor fan start on my Airwell Heat Pump?
- J
  Jonathan LeachAug 30, 2025
  If the Airwell Heat Pump indoor fan doesn't start, but the louvers are open and the Green LED is ON, there could be several reasons: * The unit is in heat mode and the coil is not yet warm: Change to cool mode. * The outdoor unit is in the opposite mode: Change the operation mode. * There's a problem with the controller or capacitor: Change to high speed and check the power supply to the motor. If the power supply is OK, replace the capacitor; if not, replace the controller.
T
tholderSep 1, 2025
Why is my Airwell Heat Pump working in the wrong mode?
- R
  rfrankSep 1, 2025
  If the Airwell Heat Pump unit operates in the wrong mode (e.g., cooling instead of heating), it could be due to electronics or RV problems. In this case, you should check the RV.
S
Shane GuerreroSep 3, 2025
Why is the Airwell Heat Pump compressor motor noisy with no suction?
- J
  Juan HernandezSep 3, 2025
  If the Airwell Heat Pump's compressor motor is generating noise but no suction is occurring, the phase order to the compressor might be incorrect. Check the compressor phase order to resolve this issue.
M
Melinda BarnettSep 5, 2025
Why does my Airwell Heat Pump's indoor fan run when OFF?
- A
  andrewskennethSep 5, 2025
  If the Airwell Heat Pump indoor fan works when the unit is OFF, and the fan speed cannot be adjusted with the remote control, it indicates a controller problem. Replace the controller to fix this.
K
Karen MccoySep 8, 2025
Why is the display off on my Airwell Heat Pump outdoor unit?
- N
  Nathaniel BergSep 8, 2025
  If the outdoor unit display board and LEDs on your Airwell Heat Pump are off, it could be due to several reasons: * No power supply: Check the connections and wiring on the main terminal and repair if needed. * PFC Chock coil: Check the PFC Chock coil. * Burnt fuse: Check the 20A fuse on the filter.