Need help?Do you have a question about the Aiwa AV-DV75 and is the answer not in the manual?
General| Total Harmonic Distortion | 0.08% |
|---|---|
| Frequency Response | 20Hz - 20kHz |
| Signal-to-Noise Ratio | 85dB |
| Digital inputs | 1 x Coaxial, 1 x Optical |
| Audio Inputs | 4 x RCA |
| Power Output | 75 watts per channel into 8 ohms (stereo) |
| Speaker Impedance | 8 Ohms |
Guidelines for safely installing the unit, covering water, heat, ventilation, and mounting.
Safety measures for connecting and using the AC power cord and plug.
Ensuring proper grounding of the antenna system for protection against voltage surges.
Important steps and checks before connecting the AC power cord.
Diagrams and instructions for connecting various audio and video devices to the receiver.
How to connect front, center, surround speakers, and sub woofer to the unit's terminals.
Setting the impedance selector for front/center speakers and guidelines for surround/subwoofer.
Instructions for connecting speaker terminals with correct polarity (+ to +, - to -).
Guidance on placing front speakers for optimal sound effect.
Recommended placement for the center speaker relative to front speakers and TV.
Instructions for placing surround speakers for optimal effect, including height and alignment.
Guidance on placing the subwoofer between the front speakers.
Instructions on how to attach the claw to stand the AM loop antenna.
Tips for positioning FM and AM antennas for best reception.
Instructions for inserting the two R6 (AA) batteries into the remote control.
Guidance on when to replace the remote control batteries based on operational distance.
Explanation of how to use the remote control buttons to operate the Aiwa receiver.
Steps to troubleshoot and reset the remote control if it fails to operate the receiver.
Instructions on how to turn the unit on and what to expect during initial operation.
How to select between speaker systems A, B, or both for audio output.
Instructions on how to set the unit to 'SUBW OFF' mode when no subwoofer is connected.
Instructions on how to turn the unit off.
Explanation of the ECO mode for reducing power consumption and how to cancel it.
How to connect headphones and the effects on sound modes.
Overview of audio adjustment controls on the unit and remote.
How to adjust the volume using the unit's control or the remote control.
How to adjust the left/right balance for the front speakers.
How to temporarily mute the sound output.
Enhancing clarity of high-frequency sound with the BBE system.
Enhancing the realism of low-frequency sound with the T-BASS system.
Storing up to 4 custom equalization curves as manual modes (M1 to M4).
Steps to turn off the graphic equalizer mode.
How to select equalizer modes using the remote control.
Adjusting the equalizer curve temporarily without saving.
How to select and adjust manual preset equalizer curves (M1-M4).
Adjusting volume and balance of surround speakers using the remote control.
Selecting DSP modes for monaural sources, and effects on surround speakers.
Steps to turn off the selected DSP surround mode.
How to select DSP surround modes using the remote control.
How to select and switch between different audio and video input sources.
Steps to select specific video input sources like VIDEO 1, VIDEO 2, or VIDEO 3.
How to rename VIDEO 1 and VIDEO 2 inputs (e.g., to DVD or MD).
Selecting between Analog or Digital input modes for video sources.
What to do when the 'OVER LEVEL' indicator lights up, and how to adjust input levels.
Adjusting the input sensitivity level for various connected sources.
Checks to perform before playing discs recorded in Dolby Digital Surround.
Steps to select the appropriate Dolby Digital Surround mode based on speaker setup.
Choosing the audio source that will be recorded.
Instructions to set the connected tape deck or MD recorder to record mode.
Initiating playback of the selected source to begin recording.
How to monitor sound during recording with a three-head tape deck.
How to tune into radio stations manually.
Using auto search to find radio stations.
How to reduce noise in FM stereo broadcasts by using the MONO TUNER button.
How to change the AM tuning interval from 10 kHz to 9 kHz steps.
How to switch back to stereo reception after using mono.
How to tune directly to stored preset stations using their numbers.
Steps to clear a stored preset radio station.
How to select preset station numbers using the remote control's UP/DOWN buttons.
How to select Dolby Digital Surround or Dolby Pro Logic modes based on speaker setup.
Recommended Dolby modes based on speaker size and presence (surround/center).
Instructions to select Dolby Surround modes using the MULTI JOG and remote buttons.
How to adjust speaker balance using the remote control's MANUAL SELECT button.
Adjusting sound levels for center and surround speakers to match front speakers.
Setting delay times for surround and center speakers in Dolby Digital Surround/Pro Logic.
Adjusting speaker balance in real-time while listening to the source.
Adjusting the dynamic range of Dolby Digital Surround sound (MIN, STD, MAX).
Adjusting the sound level of LFE signals, especially for subwoofer output.
Setting subwoofer mode to 'SUBW OFF' to redistribute LFE signals to other speakers.
Controlling TV, Cable TV, VCR, and CD player functions with the remote.
How to enter the specific ID codes for controlling external devices.
Checking the stored ID code for external equipment by counting indicator blinks.
Using the remote control's mode select buttons and other controls for external equipment.
Instructions for setting the unit's internal clock.
How to set the sleep timer to automatically turn off the receiver.
How to check the remaining time before the sleep timer turns off the unit.
Steps to disable the sleep timer function.
Detailed specifications for FM/AM tuners, amplifier, and inputs/outputs.
Details on audio and speaker output specifications.
General specifications including power, consumption, dimensions, and weight.
Instructions for cleaning the exterior cabinet of the unit.
Troubleshooting common issues like no sound or low volume.
Troubleshooting issues related to radio reception, static, and noise.
How to reset the unit to its factory default settings in case of malfunction.
To Next Page
