To Next PageTo Next Page
Need help?Do you have a question about the Alcatel-Lucent 7330 and is the answer not in the manual?
General| Category | Network Hardware |
|---|---|
| Ports | Ethernet |
| Technology | GPON, EPON |
| Management | Web-based |
| Power Supply | AC or DC |
| Dimensions | 1U height, 19-inch rack mountable |
Steps for carrying out repairs on system equipment.
Instructions for modifying Digital Subscriber Line (DSL) services.
Steps for configuring Symmetric High-speed Digital Subscriber Line (SHDSL).
Procedure for configuring Ethernet Operations, Administration, and Maintenance (OAM).
Instructions for configuring Connectivity Fault Management (CFM).
Steps for performing the initial configuration of the system.
Detailed procedures for configuring various types of equipment.
Instructions for configuring Virtual Local Area Network (VLAN) cross-connects.
Steps for configuring an iBridge Virtual Local Area Network (VLAN).
Procedure for configuring an IP-aware bridge functionality.
Instructions for configuring IP router functionalities.
Guides on configuring various network services.
Steps for locking and unlocking system equipment.
Detailed instructions for configuring the system equipment.
Procedure to configure VLANs on the Line Terminal for C-VLAN cross-connects.
Instructions to configure VLANs on the Line Terminal for S-VLAN cross-connects.
Procedure to configure VLANs for S+C-VLAN cross-connects on the Line Terminal.
Steps for configuring VLANs on the Line Terminal for C-iBridge.
Procedure to create xDSL/Ethernet users and assign them to VLANs on the Line Terminal.
Instructions for creating profiles for Digital Subscriber Line (xDSL) services.
Steps for configuring xDSL bonding for increased bandwidth.
Procedure to configure Quality of Service (QoS) parameters.
Instructions for configuring 802.1x network access control.
Steps for configuring Point-to-Point Protocol over Ethernet (PPPoE) relay on the Line Terminal.
Procedure to configure PPPoX cross-connects.
Instructions for safely shutting down and restarting the Network Termination (NT).
Steps for rebooting the entire system.
Procedure for shutting down and restarting specific equipment units.
Steps for modifying existing Digital Subscriber Line (xDSL) profiles.
Procedure to configure Secure Shell (SSH) and SFTP for secure file transfer.
Instructions for migrating users from ADSL to VDSL.
Procedure to create xDSL IPoA users and assign them to VLANs for C-VLAN cross-connects.
Steps for configuring Symmetric High-speed Digital Subscriber Line (SHDSL).
Instructions for configuring Inverse Multiplexing over ATM (IMA) on SHDSL spans.
Procedure to configure global VLAN parameters on the Line Terminal.
Steps for configuring custom Power Spectral Density (PSD) points.
Instructions for configuring VDSL2 virtual noise values.
Procedure to configure alerts for threshold crossings.
Procedure to configure Quality of Service (QoS) threshold crossing alerts.
Steps for configuring general security settings for the system.
Procedure to configure Ethernet Operations, Administration, and Maintenance (OAM).
Instructions for configuring Digital Subscriber Line (xDSL) Downstream Power Back Off profiles.
Steps for modifying xDSL Downstream Power Back Off profiles.
Procedure to configure xDSL power back off settings.
Instructions for creating IP users or subnets.
Steps for configuring the impulse noise sensor on an xDSL line.
Procedure to configure xDSL overrule data settings.
Procedure to create xDSL IPoA users and assign to VLANs for iBridge on the Line Terminal.
Instructions to configure Vectoring Control Entity profiles and associate them with boards.
Instructions to configure/modify mapping between VP board and SLV LT boards.
Steps for configuring a line with an xDSL vectoring profile.
Instructions for configuring general system parameters.
Procedure to configure the system security domain.
Comprehensive guide to fault isolation and troubleshooting.
