Alfa Laval SSV - Page 8

ALFA LAVAL UNIQUE SSV STANDARD VALVE INSTRUCTION MANUAL—REV 3/19
2 Safety
All warnings in the manual are summarized on this page.
Pay special attention to the inst ructions below so that severe personal injury and/or damage to the valve are avoided.
I
I
n
n
s
s
t
t
a
a
l
l
l
l
a
a
t
t
i
i
o
o
n
n
A
A
l
l
w
w
a
a
y
y
s
s
read the technical data thoroughly (see section )
A
A
l
l
w
w
a
a
y
y
s
s
release compressed air after use
N
N
e
e
v
v
e
e
r
r
touch moving parts if the actuator is supplied with compressed air
N
N
e
e
v
v
e
e
r
r
touch the valve or the pipelines when processing hot liquids or when sterilising
N
N
e
e
v
v
e
e
r
r
dismantle the valve with valve and pipelines under pressure
N
N
e
e
v
v
e
e
r
r
dismantlethevalvewhenitishot
!
N
N
e
e
v
v
e
e
r
r
cut the actuator open, due to spring under load
- if marked with this warning
WARNING
SPRING UNDER LOAD
DO NOT ATTEMPT TO CUT ACTUATOR OPEN
REFER TO SERVICE BULLETIN
!
AND
SPRING UNDER LOAD
Do not attempt to cut open
kg
!
Do N
N
O
O
T
T
attempt to disassemble the actuator due to spring under load danger !
DO NOT DISASSEMBLE
kg
!
O
O
p
p
e
e
r
r
a
a
t
t
i
i
o
o
n
n
N
N
e
e
v
v
e
e
r
r
dismantle the valve with valve and pipelines under pressure
N
N
e
e
v
v
e
e
r
r
dismantlethevalvewhenitishot
A
A
l
l
w
w
a
a
y
y
s
s
read the technical data thoroughly (see section )
A
A
l
l
w
w
a
a
y
y
s
s
release compressed air after use
N
N
e
e
v
v
e
e
r
r
touch the valve or the pipelines when processing hot liquids or when sterilising
N
N
e
e
v
v
e
e
r
r
touch moving parts if the actuator is supplied with compressed air
A
A
l
l
w
w
a
a
y
y
s
s
rinse well with clean water after cleaning
!
A
A
l
l
w
w
a
a
y
y
s
s
handle lye and acid with great care
M
M
a
a
i
i
n
n
t
t
e
e
n
n
a
a
n
n
c
c
e
e
A
A
l
l
w
w
a
a
y
y
s
s
read the technical data thoroughly (see section )
A
A
l
l
w
w
a
a
y
y
s
s
release compressed air after use
N
N
e
e
v
v
e
e
r
r
service the valve when it is hot
N
N
e
e
v
v
e
e
r
r
service the valve with valve and pipelines under pressure
N
N
e
e
v
v
e
e
r
r
stick your fingers through the valve ports if the actuator is supplied with compressed air
N
N
e
e
v
v
e
e
r
r
touch moving parts if the actuator is supplied with compressed air
A
A
l
l
w
w
a
a
y
y
s
s
use Alfa Laval genuine spare parts
!
N
N
e
e
v
v
e
e
r
r
cut the actuator open, due to spring under load danger
- if marked with this warning
WARNING
SPRING UNDER LOAD
DO NOT ATTEMPT TO CUT ACTUATOR OPEN
REFER TO SERVICE BULLETIN
!
AND
SPRING UNDER LOAD
Do not attempt to cut open
kg
!
Do N
N
O
O
T
T
attempt to disassemble the actuator due to spring under load danger !
DO NOT DISASSEMBLE
kg
!
T
T
r
r
a
a
n
n
s
s
p
p
o
o
r
r
t
t
a
a
t
t
i
i
o
o
n
n
A
A
l
l
w
w
a
a
y
y
s
s
ensure that compressed air is released
A
A
l
l
w
w
a
a
y
y
s
s
ensure that all connections are disconnected before attempting to remove the valve from the installation
A
A
l
l
w
w
a
a
y
y
s
s
drain liquid out of valves before transportation
A
A
l
l
w
w
a
a
y
y
s
s
use predesigned lifting points if defined
A
A
l
l
w
w
a
a
y
y
s
s
ensure sufficient fixing of the valve during transportation - if specially designed packaging material is available, it
must be used
8
CONTACT CSI FOR MORE INFORMATION | CSIDESIGNS.COM | SALES@CSIDESIGNS.COM | 417.831.1411