EasyManuals Logo

ALIBI ALI-IPV5060RP User Manual

ALIBI ALI-IPV5060RP
7 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Page #1 background imageLoading...
Page #1 background image
1
www.observint.com
ALI-IPV5060RP_CQ
11/25/14
Model Type
ALI-P50AJB Slant Mounting Base Bracket
ALI-P50JB Junction Box Bracket
ALI-P50WB Wall Mount Bracket
ALI-P5DC Ceiling Pendant Mount Bracket
Step 1. Before installing the camera ...
The ALI-IPV5060RP camera can be installed on a ceiling, wall or table, or installed with any of the optional
mounting brackets listed above.
1. Check the package contents and make sure that the device in the package is in good condition and
all the assembly parts are included.
2. Make sure the mounting surface and fasteners are strong enough to withstand at least three times
the weight of the camera assembly and the mounting bracket (if used). For concrete or cement
block walls, use an expansion screw to secure the camera or mounting bracket.
3. Make sure all the equipment that will be attached to the camera is power-o during the installation,
if possible.
4. Check the specication of the products for the installation environment.
5. Make sure the power supply is matched with the camera voltage and wattage specication to avoid
damage.
6. Make sure that there are no reective surface too close to the camera lens. The IR light from the
camera may reect back into the lens causing reection.
7. Do not remove the dome cover lm until the installation is nished. Dust or grease on the dome
cover will cause IR reection. If there is dust or grease on the dome cover, clean the dome cover with
clean soft cloth and isopropyl alcohol.
Step 2. Prepare the camera for installation
Remove the Bezel
1. Remove the camera assembly from the packaging. Do not remove the plastic lm from that covers
the lens at this time.
2. Lay the camera on a clean, at surface with the lens side up.
3. Open the Bezel Lock Screw cover.
Bezel Lock Screw
Shown with cover removed
Bezel
4. Use the security L-wrench to fully unscrew the bezel lock screw. NOTE: The bezel lock screw is a
captive screw.
5. Unsnap the cover from the camera assembly.
6. Unsnap the bezel from the camera assembly. If the bezel cannot be separated from the camera
assembly, turn the camera base side up and push a small blade screwdriver into the slots shown in
the photo below to free the three bezel retention tabs from catches on the camera assembly.
ALI-IPV5060RP 6MP 360° Fisheye
IP Camera Quick Installation Guide
This document guides you through the basic steps to install and congure the ALI-IPV5060RP cameras. The
ALI-IPV5060RP camera features:
• 1/1.8” progressive scan CMOS
• 6 mega-pixel image sensor
• Up to 3072 x 2048 resolution, 30 fps
• 360° sheye panoramic view
• Multiple viewing modes
• Internal MicroSD card slot for storage up to 64 GB (card not provided)
• Virtual PTZ mode
• 50 ft IR range
• Built-in microphone and speaker
For more information about the software features of this camera, please refer to the ALI-IP Camera
Software User Manual.
12 Vdc
Power
Bezel
Audio
OUT
Audio
LINE IN
Fisheye Lens
Alarm
IN/OUT
RJ-45 LAN
connector
RS-485
connector
Bezel lock screw under cover.
Speaker and microphone
Whats in the box
Your camera includes:
• PTZ camera assembly
• Drill template
• Network drop cable connector jacket
• Security L-wrench
• Mounting screws and wall inserts
• Software and documentation CD
• Installation and user guide (this document)
Security L-wrench and mounting hardware
Optional mounting brackets
The mounting brackets listed below are available for the ALIBI ALI-IPV5060RP camera. For more
information about using these brackets with your camera, refer to the ALI-IPV5060RP 6MP 360° Fisheye
IP Camera Installation and User Guide.

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the ALIBI ALI-IPV5060RP and is the answer not in the manual?

ALIBI ALI-IPV5060RP Specifications

General IconGeneral
BrandALIBI
ModelALI-IPV5060RP
CategoryIP Camera
LanguageEnglish

Related product manuals