EasyManuals Logo

ALIBI ALI-NS3034R User Manual

ALIBI ALI-NS3034R
6 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Page #1 background imageLoading...
Page #1 background image
1
www.observint.com
ALI-NS3034R_CQ
160315
Top (up)
Bottom (down)
Conduit port (2)
Mounting screw
hole (4)
Hole for camera
mounting screw (3)
Safety cable hook
Cable access
through mounting
surface
Camera base
locator pins
Junction box detail
Whats in the box
Your camera includes these items:
Junction box
(top view)
CD-ROM
manuals and
software
Security
L-wrench
Surface
mount drill
template
Weatherproof
LAN coupling
Mounting
hardware
packet
Video test
cable
Before installing the camera
Make sure the device in the package is in good condition and all the assembly parts are included.
Make sure all the related equipment is power-o during the installation.
Check the specication of the products for the installation environment.
Make sure the power supply is matched with your required voltage to avoid damage.
Make sure that the wall is strong enough to withstand three times (12 lb) the weight of the camera.
Dust or grease on the lens cover will cause IR reection. Please do not remove the dome cover lm
until the installation is nished. If there is dust or grease on the lens cover, clean the it with a clean
soft cloth and isopropyl alcohol.
Step 1. Install a microSD card
A microSD card installed in the camera provides local storage for log information, capture les, and
recorded video. This information can be downloaded to a network PC by accessing the camera web
interface with Microsoft Internet Explorer (see “Step 5. Login to the camera” on page 4). microSD cards
can be as large as 128GB. To install a microSD card in the camera:
1. Loosen the sun shield set screw, then lift o the sun shield.
2. Remove the lens cover from the camera body by unscrewing it counterclockwise (observing it from
the lens end).
3. Insert a microSD card into the slot shown in the photo to the left.
4. Push the microSD card into the slot until it clicks into place.
5. Reattach the lens cover and the sun shield.
Step 2. Install the camera
The camera includes hardware to install it directly to a mounting surface or to the Junction box provided.
The camera can be installed on a ceiling (horizontal surface) or wall (vertical surface). To install the camera,
do one of the following:
ALI-NS3034R IP 4 MP IR Bullet
Camera Quick Installation Guide
This document guides you through the basic steps to install and initially congure the ALI-NS3034R
camera. The ALI-NS3034R camera features:
1/3” progressive scan CMOS sensor, up to 2688 × 1520 resolution
2.8 - 12 mm motorized varifocal lens
120 dB True Day/Night (ICR), 3D DNR
-22˚F ~ 140˚F operating range
Smart IR array, 100 ft range, 850 nm
Video analytics: Tamper detection, Line crossing, Intrusion Detection
For more information, refer to these documents - available from your equipment vendor:
ALIBI™ Tools Utility Installation and User Manual
ALIBI™ Witness and ALIBI™ Witness HD Apps for Android - Quick Start Guide
ALIBI™ IP Camera Firmware Version x.x User Manual
Camera body
Lens cover
Articulated
mounting
bracket
J
unction box assembly
(see detail below)
S
un Shield
Camera mounting base
IR array
Lens
Video test cable connector
SD card slot
Reset button
Camera with sun shield and lens cover removed
* Press the RESET button for 10 seconds when the camera is powering on or rebooting to restore the
default settings, including the user name, password, IP address, the port number, etc.

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the ALIBI ALI-NS3034R and is the answer not in the manual?

ALIBI ALI-NS3034R Specifications

General IconGeneral
ModelALI-NS3034R
Night VisionYes
IR Range30m (98ft)
Video CompressionH.264
Frame Rate30fps
Operating Temperature-30°C - 60°C
Power SupplyPoE (802.3af)

Related product manuals