ALIBI ALI-NS4012R - User Manual

To Next Page

1 www.observint.com ALI-NS4012R_CQ

190708

microSD card slot Reset* button

Not used

Underside of camera body

Maintenance panel cover

* To restore the camera with its default conguration (including user name, password, IP address, etc.) press and hold the Reset

button for 10 s when the camera is power on or rebooting.

Camera maintenance panel

NOTE

The microSD card may need to be initialized before it can be used to record data. Refer to the ALIBI™

IP Camera Firmware User Manual provided at AlibiSecurity.com/resources for instructions to

initialize the card.

3. Reinstall the cover.

Step 2. Mount the camera onto a wall or ceiling

For this mounting option, the drop cables can be routed through the mounting surface, or through the

cable channel in the mounting base.

Ground

terminal

Cable

channel

Mounting

screws (3)

1. Determine the best fasteners for securing the camera mounting base to mounting surface. The

mounting hardware provided may be suitable for some surfaces.

2. Using the template provided or the camera mounting base as a template, mark the locations of

the holes for the mounting screws. Also mark the location of a hole for the camera drop cables

if needed.

3. Drill holes into the mounting surface as needed.

4. Route extension cables from the power source and LAN switch (or LAN with PoE) to the

mounting location.

5. Connect the network LAN and power extension cables to the camera drop cables:

a. Connect the Ethernet LAN cable to the camera LAN drop cable. Protect the connection

from moisture and other contamination, if necessary. A Weatherproof Ethernet Fitting is

provided. Installation instructions for the tting are included later in this document.

Network drop cable

from camera

Network cable from

router or switch

Weatherproof Ethernet Fitting installed

WARNING

Failure of the power or Ethernet connector due to moisture or another

contaminant is considered an installation error, which voids the warranty. If

installing this camera in a location such as an overhang, shop, garage, kitchen,

etc. where high humidity or dust is present, seal these connections adequately.

ALI-NS4012R 2 MP IP 100 ft IR

Bullet Camera

Quick Installation Guide

This document guides you through the basic steps to install and congure the ALI-NS4012R IP bullet

camera. This camera features:

• 1/2.8” 1920 × 1080 pixel @ 30 fps Progressive Scan CMOS sensor

• 2.8 mm lens with 108° horizontal eld of view

• Color: 0.005 Lux @ (F1.2, AGC ON), 0 Lux with IR,

Color: 0.009 Lux @ (F1.6, AGC ON), 0 Lux with IR minimum illumination

• H.265+ / H.265 / H.264+ / H.264 compression

• 120 dB Wide Dynamic Range

• 3D DNR Digital Noise Reduction

• 100 ft Full Frame IR

• Supports onboard microSD/SDHC/SDXC card storage up to 128GB (card not included)

• IP67 rated, −22 °F ~ 140 °F temperature range

For more information, refer to these documents - available from your equipment vendor:

• ALIBI™ Tools Utility Installation software and User Manual

• ALIBI™ Witness App for Android Quick Start Guide

• ALIBI™ IP Camera Firmware Version 5.4 User Manual (or later) provided at:

AlibiSecurity.com/resources

Mounting base

Lock nut

Access to microSD slot and Reset button*

Lens

Camera body

Articulated

mounting

bracket

12 Vdc Power connector with plug

Ethernet connector - PoE capable

Camera drop cables

What’s in the box

Your camera includes:

• This document

• Drill template

• Security L-wrench

• Waterproof Ethernet tting

• Mounting hardware - screws and wall

inserts

Weatherproof

Ethernet Fitting

Mounting hardware

Step 1. Install a microSD card (optional)

The camera includes hardware to install it directly to a ceiling (horizontal surface) or wall (vertical

surface). To install the camera:

1. Remove the maintenance panel cover on the underside of the camera.

2. Insert a microSD card (see Specications section for card types) into the card slot. The card

should slide in smoothly. Push the card all the way in until it latches in place.

Need help?

Do you have a question about the ALIBI ALI-NS4012R and is the answer not in the manual?

Summary

Camera Installation and Setup

Camera Features

Lists key features of the ALI-NS4012R camera, including sensor, lens, and compression.

Whats Included

Lists all accessories and components provided in the package for installation.

Install microSD Card

Instructions for inserting an optional microSD card for local storage.

Mount the Camera

Steps for physically mounting the camera unit onto a wall or ceiling.

Configuration and Activation

Install Alibi Config Tool

Guide for installing and utilizing the Alibi network device configuration utility.

Activate Alibi Device

Process for activating the camera and setting admin credentials.

Edit Network Parameters

Instructions to modify network settings like IP address and DHCP.

Camera Access and Adjustment

Login to the Camera

Steps to access the camera via its web interface using Internet Explorer.

Adjust Camera View

Guides physical camera adjustment for optimal surveillance targeting.

Camera Settings and Specifications

Image and Video Settings

Fine-tuning image parameters and video output configurations.

Technical Specifications

Detailed technical specifications of the ALI-NS4012R camera model.

Advanced Installation and Details

Waterproof Ethernet Fitting

Instructions for installing a waterproof fitting for secure Ethernet connection.

System and Interface Details

Information on compatibility, interfaces, and operating conditions.