Need help?Do you have a question about the Allen-Bradley 1756-L71 and is the answer not in the manual?
General| Product Type | ControlLogix Controller |
|---|---|
| Series | ControlLogix |
| I/O Capacity | 128, 000 I/O points |
| Communication Options | Ethernet/IP, ControlNet, DeviceNet |
| Shock | 30 g |
| Operating Temperature | 0 to 60 °C |
| Power Supply Voltage | 24V DC |
| Battery Life | 5 years |
| Relative Humidity | 5 to 95% non-condensing |
| Certifications | CE, UL, ATEX |
Warns about electrical arcs when removing/inserting modules while powered.
Explains how to install the 1756-L7x controller, summarizing tasks.
Provides step-by-step instructions for installing the SD card into the controller.
Details considerations and steps for removing the Energy Storage Module (ESM).
Provides steps for installing the Energy Storage Module (ESM) into the controller.
Lists precautions to consider before installing or removing ControlLogix controllers.
Provides guidelines to prevent damage from electrostatic discharge when handling equipment.
Warns about electrical arcs when removing/inserting modules while powered.
Lists tasks and references for installing the controller and power supply.
Explains how to install the 1756-L6x controller, summarizing tasks.
Details installation and removal steps for CompactFlash cards on series A controllers.
Details steps to remove a CompactFlash card from a series B controller.
Discusses lithium battery replacement and disposal, with warnings.
Provides steps to install a 1756-BA1 battery on a series A controller.
Provides steps to install a 1756-BA2 battery on a series B controller.
Details how to place and secure the controller into the chassis.
Details steps to remove the controller from the chassis, with warnings.
Explains the need to establish a connection before using the controller.
Explains how to connect to the controller using its USB port and required software.
Provides procedures to set up the USB driver for RSLinx software to use the USB port.
Explains how to connect to the controller using its serial port with custom or specific cables.
Guides on using RSLinx software to configure the RS232 DF1 device driver for serial communication.
Describes tools (ControlFLASH, AutoFlash) and tasks for upgrading controller firmware.
Provides step-by-step instructions for upgrading firmware using the ControlFLASH utility.
Outlines steps to upgrade controller firmware using the AutoFlash feature of RSLogix 5000.
Explains how to specify a communication path in RSLogix 5000 software to get online with the controller.
Describes methods to go online with the controller for downloading or uploading projects.
Explains how to move a project from RSLogix 5000 software to the controller.
Details downloading a project using the Who Active dialog box after setting the communication path.
Describes downloading to the controller via the Controller Status menu in RSLogix 5000 software.
Explains how to copy a project from the controller to RSLogix 5000 software.
Details uploading a project using the Who Active dialog box after setting the communication path.
Provides a table to reference controller operation modes and their meanings.
Explains how to use the physical mode switch to change the controller's operating mode (RUN, REM, PROG).
Describes changing the operation mode using the Controller Status menu in RSLogix 5000 software.
Explains using the memory card to load or store user memory contents for the controller.
Details steps to store a project to the memory card after being online and in Program mode.
Details steps to load a project to the controller from the memory card after being online and in Program mode.
Explains using ESMs to provide power for saving programs or clearing memory.
Provides steps to save the program to NVS memory when the controller loses power.
Explains how to monitor and maintain lithium batteries supported by ControlLogix controllers.
Describes low-battery warnings and when to replace a battery.
Details how to estimate battery life for series A controllers.
Provides a table to estimate battery life before the BAT status indicator turns red.
Provides a table to estimate battery life after low-battery warnings are indicated.
Lists system components to consider when designing a ControlLogix system.
Explains EtherNet/IP network services, protocols, and components for cost-effective solutions.
Describes ControlNet as a real-time network for high-speed data transport and synchronization.
Describes DeviceNet network using CIP for industrial devices, leveraging CAN technology.
Explains DH+ communication using the 1756-DHRIO module for information exchange.
Guides on using RSLinx Classic software for DH+ network communication.
Lists module options for universal remote I/O communication in ControlLogix chassis.
Details steps to add local I/O modules to the backplane in RSLogix 5000.
Details steps to add remote I/O modules to the backplane of a communication module.
Details steps to add distributed I/O modules to the controller's I/O configuration.
Explains reconfiguring I/O modules via Module Properties or a MSG instruction.
Details reconfiguring an I/O module using its properties in the I/O Configuration tree.
Details reconfiguring an I/O module using a Module Reconfigure message instruction.
Explains adding I/O and devices to the configuration while online in Run mode.
Provides a procedure for building a typical redundant system.
To Next Page
