Alliance Laundry Systems AWN432SP113TW01

Questions and Answers

T
Thomas GibsonAug 17, 2025
Why won't my Alliance Laundry Systems Washer fill with water?
- C
  Christina MurrayAug 17, 2025
  Several factors could be preventing your washer from filling. First, ensure the power cord is fully plugged into the electrical outlet and that both hot and cold water faucets are turned on. Check that the fill hoses are not kinked or twisted. Pull the timer knob out to start the washer and verify the controls are properly set. Note that the Normal Eco cycle uses a spray rinse instead of filling the tub during the rinse portion. Ensure the last spin cycle has been completed, and check the laundry room fuse or circuit breaker. Clean the screens in the water mixing valve and the filter screens at the faucet end of the fill hoses. Finally, improper drain hose installation can cause siphoning; refer to the installation instructions to confirm correct setup.
S
Sherry WarrenAug 20, 2025
What to do if my Alliance Laundry Systems Washer won't start?
- M
  Maria WilliamsAug 20, 2025
  If your washer isn't starting, begin by ensuring the lid is completely closed and the timer knob is pulled out. Verify the power cord is fully plugged into the electrical outlet and that the controls are correctly set. Check the laundry room fuse or circuit breaker. Also, the motor overload protector may have stopped the cycle; it will reset itself in a few minutes and automatically restart the washer.
C
Chris SmithAug 22, 2025
Why does my Alliance Laundry Systems Washer stop during the cycle?
- J
  Julie GarrettAug 22, 2025
  Pauses during the cycle are a normal part of the washer's operation. The washer will stop (pause) shortly before the wash and rinse spins. However, if the pauses seem unusual, check the laundry room fuse or circuit breaker. The motor overload protector may also have stopped the cycle; it will reset itself in two or three minutes and restart the washer automatically.
J
Jessica HopkinsAug 26, 2025
How to fix a noisy Alliance Laundry Systems Washer?
- J
  jasmine42Aug 26, 2025
  A noisy washer can often be attributed to an unbalanced load; try opening the lid and redistributing the items. Ensure the washer is level, as uneven leveling can cause vibration. If the washer is newly installed, a knocking sound may occur due to the belt settling after storage; running the washer through 4-5 cycles should resolve this.
A
Alexander HansenAug 28, 2025
What to do if my Alliance Laundry Systems Washer won't drain?
- B
  bobby04Aug 28, 2025
  If your washer isn't draining, check that the drain hose is not kinked, twisted, or clogged. Also, ensure the drain receptacle itself isn't clogged. Refer to the Installation instructions to verify the drain hose has been properly installed.
O
oleeAug 31, 2025
Why is my Alliance Laundry Systems Washer load too wet after washing?
- R
  Roy MorganAug 31, 2025
  If the wash load is too wet after washing, it may be unbalanced. Try opening the lid and redistributing the load. Alternatively, the load might be too small; adding more items to create a full load can help.
D
Donald Case DDSSep 2, 2025
How to troubleshoot water leaks in my Alliance Laundry Systems Washer?
- J
  Jacob OsbornSep 2, 2025
  To address water leaks, first check that the fill hoses are properly installed on both the faucets and the washer's water mixing valve. Inspect the condition of the fill hoses, replacing them every five years. Ensure the drain receptacle is not clogged and check your laundry room plumbing. Also, verify your house water pressure, as extremely low pressure can sometimes cause leaks. Finally, the laundry load may be oversudsing or overloaded; use less detergent (or a low-sudsing detergent) and ensure proper load sizes.
C
Christopher TerrellSep 5, 2025
Why won't my Alliance Laundry Systems Washer agitate?
- K
  Kevin FuentesSep 5, 2025
  If your washer isn't agitating, make sure the lid is closed and the timer knob is pulled out to start the washer. Check that the power cord is fully plugged into the electrical outlet and the laundry room fuse or circuit breaker. The motor overload protector may have stopped the cycle; it will reset itself in a few minutes and restart the washer automatically. If these steps don't resolve the issue, the drive belt may be broken, and you should call a service person.
J
Joseph SmithSep 7, 2025
Why is my Alliance Laundry Systems Washer not spinning?
- E
  Edward GilesSep 8, 2025
  If your washer isn't spinning, ensure the lid is closed and the timer knob is pulled out to start the washer. Verify the power cord is fully plugged into the electrical outlet and check the laundry room fuse or circuit breaker. The motor overload protector may have stopped the cycle; it will reset itself in two or three minutes and restart the washer automatically. If the issue persists, the drive belt may be broken, and you should contact a service person.
S
Sharon WoodSep 12, 2025
Why is my Alliance Laundry Systems Washer using the wrong water temperature?
- D
  David BarrettSep 12, 2025
  If your washer is using the wrong water temperature, first ensure that the controls are properly set. Check the fill hoses to make sure the hot faucet hose is connected to the hot mixing valve (marked with “H”) and the cold faucet is connected to the cold mixing valve (marked with “C”). Also, verify that your laundry room water heater is adjusted properly. Keep in mind that the Normal Eco cycle only uses cold water.

Summary

Front Matter

General Safety Warnings

Contains critical warnings about installation, operation, and potential hazards.

Important Usage Notes

Highlights the need for common sense and caution when operating the washer.

Product Registration

Warranty Registration

Encourages owners to register their appliance online or with their dealer for warranty coverage.

Safety Information

Explanation of Safety Messages

Defines DANGER, WARNING, CAUTION, IMPORTANT, and NOTE symbols used in the manual.

Important Safety Instructions

Lists crucial safety rules for operating the washing machine to prevent injury or damage.

General Operating Safety

Outlines safety precautions during washer operation, including guards, tampering, and chemical handling.

Operation

Prepare Wash Load

Instructions on emptying pockets, mending, checking colorfastness, and sorting clothes before washing.

Pretreat Stains

Advice on pretreating collars, cuffs, and specific stains before loading.

Loading the Washer

Guidance on adding detergent first and properly loading items into the washtub.

Load Articles and Size

Details on how to load items, determine load size, and ensure correct water levels.

Wash Temperature Guide

Explains the use of Hot, Warm, and Cold water for different fabric types and soil levels.

Energy Saving Tips

Provides guidelines for conserving energy during washing cycles.

Operating Your Washer

Determine Proper Cycle

Explains various wash cycles like Heavy Duty, Normal Eco, Handwash/Delicate, and Soak/Prewash.

Extra Rinse Option

Describes the optional Extra Rinse feature for sensitive skin.

Washing Clothes Steps

Step-by-step instructions on how to prepare and start a wash cycle.

Timer Operation

How to use and reset the washer's timer for cycle control.

Manual Soaking

Procedure for manual soaking of clothes.

Optional Features: Dispensers

Information on using the bleach and fabric softener dispensers.

Clothing Care

Clothing Concerns and Solutions

Addresses common clothing issues like dinginess, yellowing, tearing, and staining with causes and solutions.

Lint and Wrinkling Solutions

Further advice on managing excessive lint and preventing wrinkles in clothes.

Maintenance

Cold Weather Care

Precautions for operating or storing the washer in freezing temperatures.

Washer Cleaning and Care

Guidelines for cleaning the control panel, cabinet, and washtub.

Hose and Filter Maintenance

Instructions for checking and replacing hoses and cleaning filter screens.

Extended Non-Use and Preventative Checks

Advice for vacations and routine checks to ensure proper operation.

Shipping Materials Reinstallation

Procedures for reinstalling shipping brace and plug when moving the washer.

Motor Overload Protector

Explanation of the motor overload protector and its function.

Control Knob Inserts

Information on optional color inserts for control knobs.

Troubleshooting

Washer Wont Fill or Start

Solutions for common issues where the washer does not fill or start.

Washer Wont Agitate

Troubleshooting steps for when the washer fails to agitate.

Spin, Drain, and Noise Issues

Addresses problems like the washer not spinning, not draining, or making noise.

Water Leaks and Load Issues

Solutions for water leaks, oversudsing, overloading, and unbalanced loads.

Water Temperature and Level Problems

Diagnoses and resolves issues related to wrong water temperature or low water level.

Contact Information

Service and Parts Support

Where to contact for service, parts, and online support.

Identifying Your Washer

Guidance on locating the model and serial number for service inquiries.

Alliance Laundry Systems AWN432SP113TW01 Specifications

General

Brand	Alliance Laundry Systems
Model	AWN432SP113TW01
Category	Washer
Type	Top Load
Capacity	3.2 cu. ft.
Top Load Capacity	3.2 cu. ft.
Voltage	120 V
Phase	1
Amperage	15 A
Frequency	60 Hz
Door Type	Top Load
Energy Star Certified	No
Width	27 in
Agitator Type	Agitator
Top Load Cycle Options	Normal, Heavy Duty, Delicate
Height	43 in