EasyManua.ls Logo

Allsteel CONCENSYS CAPE User Manual

Default Icon
52 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Page #1 background imageLoading...
Page #1 background image
2210 Second Avenue
Muscatine, IA 52761-5257
70-0010
0 6 /07/ 11
MODEL: CAPE
IM PORTANT
CONCENSYS
®
INSTALL ATION
INSTRUCTIONS INSIDE
ENGLISH VERSION
POUR DES INSTRUCTIONS EN FRANCAIS,
APPELER LE 800-822-7653
PARA INSTRUCCIONES EN ESPANOL,
LLAME AL 800-822-7653
6 31530 52006 7

Table of Contents

Question and Answer IconNeed help?

Do you have a question about the Allsteel CONCENSYS CAPE and is the answer not in the manual?

Allsteel CONCENSYS CAPE Specifications

General IconGeneral
BrandAllsteel
ModelCONCENSYS CAPE
CategoryIndoor Furnishing
LanguageEnglish

Summary

Panel Systems Guidelines

Adequate Stability Methods

Describes methods for ensuring panel stability using return panels.

Notes and Definitions

Provides important notes on return panel height and definitions of terms.

Overhead Storage Unit Installation

Installation Guidance

General instructions for installing overhead storage units on panels.

Panel Connectors

Basic Panel Connection

Step-by-step guide for connecting panels using vertical connectors.

Top Cap Installation

Instructions for installing cableway and low-profile top caps.

Baserail Cover Installation

Guides for removing and installing baserail covers.

End Connector Kit Installation

Procedures for installing end connector kits for cableway and low-profile options.

Wall Connector Kit Installation

Steps for installing wall connector kits, including marking and connections.

Marking Wall Connector Location

How to mark the wall for precise wall connector placement.

Direct to Wall Connection

Method for directly attaching wall connectors to the wall.

Offset Wall Connection

Instructions for offset wall connections, allowing for panel compatibility.

Top Cap Connections

Details on connecting low-profile and cableway top caps to wall connectors.

Variable Height Connection

Guidance on making variable height connections using specific brackets and fillers.

Panel Door Installation

Connecting Door to Panels

How to connect a door panel to standard 82" high panels.

Converting Door Orientation

Steps to convert a right-hand door to a left-hand orientation.

Connecting Door to Wall Connector

Instructions for connecting the door panel to a wall connector kit.

Lowering Threshold to Floor

Adjusting the door threshold to rest properly on the floor.

Countertops and Wood Shelves

Countertop Installation

Procedures for installing countertops, including support brackets.

Wood Shelves Installation

Steps for installing wood shelves using support brackets and screws.

Overhead Storage Units

Attaching and Removing Storage Units

How to attach and remove overhead storage units from panels.

Shelf Divider Installation

Guide for installing the optional shelf divider accessory.

Shelf Unit Ganging

Instructions for ganging overhead shelf units together for stability.

Storage Unit Ganging

Method for ganging overhead storage units using straps and hinge brackets.

Peninsula, D-Top, and Quarter-Round Worksurfaces

Support Column Attachment

Steps for attaching support columns to worksurfaces.

Peninsula Attachment to Panel

How to attach peninsula worksurfaces to panels using support brackets.

Peninsula Attachment to Worksurface

Guide for attaching peninsula worksurfaces to primary worksurfaces.

D-Top Installation

Instructions for installing D-top worksurfaces with tie brackets.

Worksurface Supports

General Arrangement Overview

Illustrates various worksurface support configurations.

Safety and Important Notes

Warnings and important information regarding worksurface support usage.

Full End Panel Support Assembly

Steps to assemble the full end support panel for worksurfaces.

Attaching Brackets to Panel Frame

How to attach panel attachment and anti-dislodgement brackets.

Attaching Support to Worksurface

Process for attaching the full end panel support to the worksurface.

Support Leg Assembly

Instructions for assembling support legs for panel junctions.

Important Usage Notes

Key considerations for using support legs, including grommet hole blocking.

Center Support Bracket Installation

Guide for installing center support brackets for longer worksurfaces.

Worksurface-to-Panel Support Bracket Installation

Steps for installing worksurface-to-panel support brackets.

Worksurface Bracket Kit Installation

How to install right-hand and left-hand worksurface brackets.

Cantilever Support Bracket Preassembly

Preassembly instructions for cantilever support brackets for different applications.

Cantilever Bracket Installation onto Panels

Method for hanging cantilever brackets onto panels.

Flat Bracket Installation

Instructions for attaching flat brackets to worksurfaces.

Corner Support Bracket Installation

Guide for installing corner support brackets at the rear of worksurfaces.

Flexconnect Electrical System Installation

General Configuration and Component Identification

Overview of Flexconnect system configuration and component identification.

Electrical Wiring Diagrams

Wiring diagrams for different phase and phase supply configurations.

Powering Last Panel

Guidelines for powering the last panel in a run or at an end.

Harness Installation in Baserail Area

How to install power and pass-thru harnesses in the baserail area.

Power Block Removal

Instructions for removing power blocks from mounting brackets.

Receptacle Installation/Removal

Procedures for installing and removing receptacles from power blocks.

Terrace Series: BeltLine Area Installation

Electrical installation within the beltline area for the Terrace series.

Terrace Series: BeltLine to Baserail Connection

Connecting electrical components from beltline to baserail in Terrace series.

Terrace Series: Other Area Installation

Electrical installation guidance for areas other than baserail and beltline.

Stride Series: Beltline Area Installation

Electrical installation within the beltline area for the Stride series.

Stride Series: Beltline to Baserail Connection

Connecting electrical components from beltline to baserail in Stride series.

Stride Series: Ceiling In-Feed to Baserail Area

Installing ceiling in-feed connections into the baserail area for Stride.

Stride Series: Ceiling In-Feed to Beltline Area

Installing ceiling in-feed connections into the beltline area for Stride.

All Series: Base/Ceiling Side In-Feed Installation

Detailed steps for base or ceiling side in-feed installation for all series.

8000 Series: Ceiling In-Feed to Baserail

Installing ceiling in-feed connections into the baserail area for the 8000 Series.

Concensys: Ceiling In-Feed with Integrated Power Pole

Installing ceiling in-feed using an integrated power pole for Concensys.

Stride/Terrace: Ceiling In-Feed to Baserail

Ceiling in-feed installation to baserail for Stride/Terrace series.

Terrace: Ceiling In-Feed to Beltline Area

Installing ceiling in-feed connections into the beltline area for Terrace.

Integrated Power Pole Installation

Power Pole Assembly and Preparation

Steps for assembling and preparing the power pole for installation.

Power Pole Cover Installation

How to install the power pole cover and ceiling trim plates.

Connecting Power Source

Instructions for connecting the power pole to the building power source.

Permanent Wall Hanger Kit Installation

Hardware and Safety Precautions

Required hardware and critical safety warnings for the kit.

Mounting Hole Locations and Fasteners

Specifies appropriate fasteners for different mounting hole locations.

Positioning Slotted Standards

Guidance on positioning slotted standards for modularity with panels.

Freestanding Desk Applications

Full End Panel Support Configuration

How to configure full end panel supports for left or right-hand applications.

Primary Desk with Modesty Panel

Steps for assembling a primary desk with a modesty panel.

Primary Desk with Gussets

Instructions for installing gussets on a primary desk for stability.

Attaching Modesty Panel Bracket for Bridge/Return

How to attach modesty panel brackets for bridge or return configurations.

Attaching Return or Bridge to Primary Desk

Procedures for attaching return or bridge worksurfaces to the primary desk.

Attaching Support Legs

How to attach desk support legs to peninsulas or corner desks.

Attaching Return/Bridge to Peninsula Worksurface with Support Leg

Guide for attaching return or bridge worksurfaces using a support leg.

Corner Desk Assembly

Steps for assembling a corner desk configuration.

Technology Panel Installation

Panel Components and Overview

Introduction to technology panel components and general layout.

Tile Removal and Replacement

Procedures for removing and reinstalling panel tiles, including the beltline cover.

Worksurface and Data Module Placement

Guidelines for worksurface positioning and data module integration.

Routing Electrical Harness

Methods for routing electrical harnesses from adjacent panels.

Routing Jumper Cables

Instructions for routing electrical jumper cables between panels.

Stacking Panel Installation

Glass Panel Disassembly

Steps to disassemble glass stacking panels before installation.

Attaching Glass Stacking Panel to Base Panel

Guide for attaching glass stacking panels to base panels using connectors.

Fabric Panel Disassembly

Steps to disassemble fabric stacking panels before installation.

Attaching Fabric Stacking Panel to Base Panel

Guide for attaching fabric stacking panels to base panels using connectors.

Stacking Panel Configurations

Requirements for single/double high stacking panel configurations and connectors.

Brackets and Transition Pieces

Table listing required brackets and transition pieces for various panel configurations.

Panel End Cover Requirements

Specifies when full-length or 13" panel end covers are required for stability.

Adequate Stability Methods for Stacking Panels

Outlines methods for achieving stability with stacking panels above 82" height.

Related product manuals