Alpine 7279M - Page 5

CONNECTIONS
OPERATION
——_ «Antenna Receptacle
= ——— ES)
White/Black a . Left Speaker Output Lead common)
— ee,
Gray/Black aoe = Right Speaker Output Lead {common}
ne Left Front Speaker Output Lead
| Whrte _
—— eS) Right Front Speaker Output Lead
Grey —
SE CES Left Rear Speaker Output Lead
| Green —_—
eS Right Rear Speaker Output Lead
Blue/Whre —_
Remote ON Lead
Red —
fae © ACC Power Lead
—s
Lc
ee
Baiery
lesa
Ground Lead
ist
id
‘TAPE PLAYER OPERATION>
1.
Turn the power on by rotating the VOLume control/power
switch @ clockwise. With the tapa opening to the right, in-
sert the cassette into the loading slot as far as it will go. One
of the tape direction indicators @ will light and the tape will
Start playing.
If a metal or CrO, cassette tape is inserted, the tape mecha-
nism automatically sets itself for 70ssec equalization.
Adjust VOLume @, BASS @, TREBle @, BALance 4 and
FADer 2 controls to suit your listening preference. Tape re-
verses automatically at the end of the tape to play the other
side.
Tochange from side A to play side B or vice versa before the
end of the tape is reached, press the PROGRAM switch 4).
To stop tape play, press the EJECT switch ®.
Toturn the power OFF, fully rotate the VOLume control coun-
terclockwise.
Winding the Tape Rapidly in Forward or Reverse Direction
dh
2
3.
Press the PROGRAM Switch ( 44 or »» button) 6) until it
locks and the tape will run rapidly in the designated direction.
Lightly press the other button to stop. the Fast Winding
mode. The tape will start playing again.
When the Fast Winding operation reaches the end of the
tape, the mode will automatically switch to playback.
AUTO PAUSE
When the unit is removed from its bracket, it automatically goes
into the Tape Pause Mode, the tape disengages from the cap-
stan and pinch roller. When the unit is re-inserted into the brack-
et, tape play will resume from the point in which it was stopped.
Key-off Pause
If the ignition is turned off while a cassette is playing, the tape
disengaqas from the tapa head, capstan, and pinch roller, but
the cassette remains in the cassette compartment with the cas-
sette door completely closed. When the ignition switch is
turned on again, playback will begin from the point where it was
left off.
i Violet _ Right
5 Red Output RCA Type Connector
Left
White
Blue
Power Antenna Lead
727T9M/L/E
Output RCA Type connectors
RCA type connectors are for connecting the unit to
an unit having RCA type input terminals.
Power Antenna Lead
Connect the power antenna control lead (Blue) to the
connector of full automatic power antenna. Power
antenna control does not work with semi-automatic
or manually operated antenna.
ACC Power Lead
This lead is to be connected to an ignition terminal in
the vehicle’s fuse box or a terminal which develops
+ 12 V when the ignition is turned on.
Remote ON Lead
If the unit is connected to your Amp unit with RCA
jacks, connect the remote ON lead to the male con-
nector of the unit remote ON lead.
CAUTION:
Before connecting any wire, set the volume level to
minimum by turning the power ON/OFF switch knob
counterclockwise.
Radio Monitor (7279L/E models only)
Pushing the RADIO MONITOR/LOUDNESS switch @, Radio
Monitor is activated and R MONI indicator @ will light, you can
receive the last tuned station or operate seek tuning UP @3 and
DOWN 42. Push this switch for 3 seconds or more to activate
LOUDNESS function; LOUD indicator lights up. Low frequency
sound will be boosted at low sound contents. Push the switch
again for 3 seconds or more to release the function.
«RADIO OPERATION»
MANUAL and AUTOMATIC SEEK TUNING (7279M/L models
only)
The radio does not operate in the tape play mode. Tolisten to the
radio, eject the cassette by pressing the EJECT switch @).
Pressing the EJECT switch ® during tape play causes the tape
in the loading slot to be ejected.
1. Turn on the power by turning the VOLume control/Power
OFF switch @ clockwise. Continue to rotate it until the de-
sired volume level is reached.
2.. Push Radio BAND select switch @® for reception of MW/LW
or FM (FM 1 or FM2). The radio BAND Indicator @ will be on,
and the ST [stereo] indicator @ will also be on during FM
stereo reception.
3. Adjust BASS ©, TREBle @, BALance @, and FADer @ con-
trols to their center positions.
4. To automatically tune, press the SEEK TUNE button 19 and
then either UP or DN tuning button. The SEEK indicator @ ap-
pears on the display and the frequency changes to indicate
that the radio is in the auto SEEK tuning mode and ready to
stop at every strong station. Repeat the procedure until your
desired station is obtained. When the radio reaches the up-
per or lower end of the band, it automatically starts scanning
in the opposite direction. To return to manual tuning, press
the SEEK TUNE button again, the SEEK indicator disappears.
5. Tomanually tune, press the Tuning Switch (UP) 43 for higher
frequency broadcasts, and press the Tuning Switch (DN)
for lower frequency broadcasts.
Sabi