Alpine 7513L - CD Player and Clock Operations; CD Player Functions; Detachable Front Panel Handling

7513M/7513L
7514M/7514L
7513M/7513L
7514M/7514L
OPERATION
OPERATION
|
OPERATION
Fast Forward/Fast Backward
The fast forward/fast backward feature works in the play mode only.
Press either the FF © or the REW © switch and hold it down for more than 1 second.
To move the pickup forward rapidly, hold down the FF switch ©.
To move the pickup backward rapidly, hold down the REW switch ©.
Release the switch when you get to the desired position on the disc.
When the pickup reaches the end of the disc, it will begin playback from the beginning
of the first track on the next disc.
SQN
Repeat (One/AIll)
This feature allows you to continuously repeat a single track or one entire disc.
To Repeat a Single Track
1, Locate the music track of your choice using the UP © or DN ® switch.
2. Press the REPEAT button @.
The REPEAT indicator 8 will illuminate on the Digita! display @.
The music track will be played back repeatedly.
3. To stop repeat play, press the REPEAT button @ twice.
To Repeat an Entire Disc
1. While playing a disc, press the REPEAT button @ until the ALL indicator @ will
illuminate.
2. The disc will be played back repeatedly.
3. To stop repeat play, press the REPEAT button @ once. The indicator illumination will
be off.
M.LX. (Random Play)
Press the M.I.X. button © (for more than 2 seconds: 7514L/7513L only) while the unit
is in the play or pause mode. Musical tracks on the selected disc will be played back in a
random sequence generated by the microprocessor. After all the tracks on the disc have
been played back once, the player will begin a new random sequence.
@ CLOCK OPERATION
To display Clock Indication
aoe
the
CLOCK
button
@.
The
display
will
indicate
the
clock
indication.
E:
if
the
unit
power
is
off.
The
unit
shows
the
clock
time
unless
the
vehicle's
ignition
switch
is
not
off.
2.
To
turn
off
the
clock
indication,
press
the
CLOCK
button
@
again.
Clock
display
priority
function
Has
the
clock
time
is
being
displayed,
the
unit
is
set
to
the
“Clock
display
priority
mode”.
When
an
operation
of
FM,
MW,
LW,
Cassette,
etc.
is
conducted,
that
operation
mode
is
once
indicated
on
the
display,
but
the
clock
indication
is
automatically
resumed
after
5
seconds.
Setting the Time
1.
Press
and
hold
the
CLOCK
button
@
for
at
least
3
seconds
to
enable
the
time
adjust
mode.
The
time
display
will
blink
when
ready
for
setting.
2. Adjusting the hours:
Use Hour button ® to adjust the hours
3. Adjusting the minutes:
Use Minute button @ to adjust the minutes.
4. Initializing the minutes and seconds:
Pressing
Clock
Time
button
@
will
set
the
minutes
and
seconds
to
zero.
@ Handling the Detachable Front Panel
Removal
1. Press the PWR button ©® to turn the power off.
2. Press the Release button. (Fig. 2)
3. The detachable front panel pops out. Grasp part of it and pull it off. (Fig. 3)
NOTE:
After removing the detachable front panel, place it in the included case and protect it
from strong shocks and dirt.
Installation
1. Check that there is no dirt, etc., in the grooves on the ends of the detachable unit.
Insert the right side of the detachable panel first, as shown in Fig. 4.
2. Press on the detachable front panel at a point other than the button surface on the left
side until a click is heard. (Fig. 5)
3. Touch the detachable front panel and check that it is securely fastened.
NOTE:
Be sure to check that there is no dirt, dust, etc., on the connector terminals for the
detachable face and unit before installing it.