29-EN
3
Turn the Rotary encoder to adjust the level.
Adjustable level: -6 to +6 dB
4
Press SOURCE/ to set the bandwidth (Q).
Adjustable bandwidth: 1, 1.5, 3
5
To adjust another band, repeat steps 4 to 7 and
adjust all bands.
• The frequencies of adjacent bands cannot be adjusted within 4 steps.
• While adjusting the PARAMETER EQ, you should consider the
frequency response of the connected speakers.
Adjusting the Graphic Equalizer Curve
You can modify the equalizer settings to create a response curve more
appealing to your personal taste. To adjust the graphic equalizer curve,
set the EQ MODE to GRAPHIC EQ. For details, refer to “Setting EQ
mode” (
page 28).
1
After selecting GRAPHIC EQ from the SOUND
ADJUST mode, press BAND/TA to select the band
to be adjusted.
B 1 B 2 B 3 B 4 B 5 B 6 B 7 B 1
Band-1 (63 Hz) / Band-2 (150 Hz) / Band-3 (400 Hz) /
Band-4 (1 kHz) / Band-5 (2.5 kHz) / Band-6 (6.3 kHz) /
Band-7 (17.5 kHz)
2
Turn the Rotary encoder to adjust the level.
Adjustable output level: -6 to +6 dB
3
To adjust another band, repeat steps 1 and 2, and
then adjust all bands.
Adjusting the Time Correction
Before performing the following procedures, refer to “About Time
Correction” (
page 31).
1
After selecting T.CORRECTION from the SOUND
ADJUST mode, press BAND/TA to select a speaker
to be adjusted.
2.2ch (3WAY) System
4.2ch (FRONT/REAR/SUBW.) System
2
Turn the Rotary encoder to adjust the distance
correction value (0.0 to 336.6cm).
L = (distance to farthest speaker) – (distance to other
speakers)
Refer to “Time Correction Value List” on page 31.
3
Repeat steps 1 and 2 to set another speaker.
By setting these values to make its sound reach the
listening position at the same time as the sound of other
speakers.
Adjusting the Crossover Settings
Before performing the following procedures, refer to “About the
Crossover” (
page 32).
2.2ch (3WAY) System
1
After selecting CROSSOVER from the SOUND
ADJUST mode, press BAND/TA to select the band
to be adjusted.
2.2ch (3WAY) System / NORMAL (L=R)
Setting items:
LOW / M-L / M-H / HIGH
2.2ch (3WAY) System / INDIVIDUAL (L/R)
Setting items:
L-L / L-R / ML-L / ML-R / MH-L / MH-R / H-L / H-R
2
Press or to select the desired cut-off frequency
(Crossover Point).
Adjustable frequency bands:
2.2ch (3WAY) System
Setting items:
LOW / M-L 20 Hz~200 Hz
M-H 20 Hz~20 kHz
HIGH (1 kHz~20 kHz)*
1
/(20 Hz~20 kHz)*
2
*
1
When Maker’s is selected, refer to “Setting the Response Slope for
the High Range Speaker (TW SETUP)” (
page 27).
*
2
When User’s is selected, refer to “Setting the Response Slope for the
High Range Speaker (TW SETUP)” (
page 27).
F-L (Initial setting)
F-R R-L R-R
(Mid-L) (Mid-R) (High-L ) (High-R)
SW-L SW-R F-L
(Mid-L)
F-L (Initial setting)
F-R R-L R-R
(Front-L) (Front-R) (Rear-L) (Rear-R)
SW-L SW-R F-L
(Front-L)
To Next Page
Loading...
Need help?
General
