Alpine CDA-9887R - Setting the Time Correction Unit; Adjusting and Storing the Time Correction

21-EN
01GB05CDA-9887R.fm
ALPINE CDA-9887R 68-08564Z21-A (EN)
Time Difference Table
Setting the Time Correction Unit
You can change the unit, (cm or inch) of time correction.
1 Press and hold FUNC./SETUP for at least 2
seconds to setup the Selection mode.
2 Turn the Rotary encoder to select AUDIO mode,
and then press //ENT.
Bluetooth GENERAL AUDIO DISPLAY
TUNER Bluetooth
3 Turn the Rotary encoder to select T.CORR
Parameter mode, and then press //ENT.
4 Turn the Rotary encoder to select the desired
items, and then press //ENT.
T.CORR Parameter<cm> T.CORR Parameter<inch>
(Initial setting)
5 After setting, press and hold FUNC./SETUP for at
least 2 seconds to return to normal mode.
• Pressing AUDIO/RTN during the procedure will return to the
previous mode.
• If no operation is performed for 60 seconds in the SETUP mode, the
setting mode is cancelled.
• Press and hold /ESC for at least 2 seconds, the setting mode is
cancelled.
Adjusting and Storing the Time Correction
Before performing the following procedures, refer to “About Time
Correction” (page 20).
1 Press A.SEL to recall the DSP adjust mode.
Media Xpander Crossover T.Correction
Parametric EQ / Graphic EQ Media Xpander
2 Turn the Rotary encoder to select the T.Correction
mode, and then press //ENT.
3 Press BAND/TA to select a speaker to be adjusted.
2.2ch (3WAY) System
L-F (Initial setting) R-F L-R
(Mid-L) (Mid-R) (High-L)
R-R L-SW R-SW L-F
(High-R) (Mid-L)
4.2ch (F/R/Sub-W) System
L-F (Initial setting) R-F L-R
(Front-L) (Front-R) (Rear-L)
R-R L-SW R-SW L-F
( Rear -R) ( Front -L)
4 Turn the Rotary encoder to adjust distance
(0.0 to 336.6 cm).
Delay
Number
Distance
(cm)
Distance
(inch)
Delay
Number
Distance
(cm)
Distance
(inch)
0 0.0 0.0 51 173.4 68.3
1 3.4 1.3 52 176.8 69.7
2 6.8 2.7 53 180.2 71.0
3 10.2 4.0 54 183.6 72.4
4 13.6 5.4 55 187.0 73.7
5 17.0 6.7 56 190.4 75.0
6 20.4 8.0 57 193.8 76.4
7 23.8 9.4 58 197.2 77.7
8 27.2 10.7 59 200.6 79.1
9 30.6 12.1 60 204.0 80.4
10 34.0 13.4 61 207.4 81.7
11 37.4 14.7 62 210.8 83.1
12 40.8 16.1 63 214.2 84.4
13 44.2 17.4 64 217.6 85.8
14 47.6 18.8 65 221.0 87.1
15 51.0 20.1 66 224.4 88.4
16 54.4 21.4 67 227.8 89.8
17 57.8 22.8 68 231.2 91.1
18 61.2 24.1 69 234.6 92.5
19 64.6 25.5 70 238.0 93.8
20 68.0 26.8 71 241.4 95.1
21 71.4 28.1 72 244.8 96.5
22 74.8 29.5 73 248.2 97.8
23 78.2 30.8 74 251.6 99.2
24 81.6 32.2 75 255.0 100.5
25 85.0 33.5 76 258.4 101.8
26 88.4 34.8 77 261.8 103.2
27 91.8 36.2 78 265.2 104.5
28 95.2 37.5 79 268.6 105.9
29 98.6 38.9 80 272.0 107.2
30 102.0 40.2 81 275.4 108.5
31 105.4 41.5 82 278.8 109.9
32 108.8 42.9 83 282.2 111.2
33 112.2 44.2 84 285.6 112.6
34 115.6 45.6 85 289.0 113.9
35 119.0 46.9 86 292.4 115.2
36 122.4 48.2 87 295.8 116.6
37 125.8 49.6 88 299.2 117.9
38 129.2 50.9 89 302.6 119.3
39 132.6 52.3 90 306.0 120.6
40 136.0 53.6 91 309.4 121.9
41 139.4 54.9 92 312.8 123.3
42 142.8 56.3 93 316.2 124.6
43 146.2 57.6 94 319.6 126.0
44 149.6 59.0 95 323.0 127.3
45 153.0 60.3 96 326.4 128.6
46 156.4 61.6 97 329.8 130.0
47 159.8 63.0 98 333.2 131.3
48 163.2 64.3 99 336.6 132.7
49 166.6 65.7
50 170.0 67.0
01GB00CDA-9887R.book Page 21 Thursday, March 15, 2007 3:55 PM