32-EN
01GB05CDA-9887R.fm
ALPINE CDA-9887R 68-08564Z21-A (EN)
Controlling CD Changer (Optional)
An optional 6-disc or 12-disc CD Changer may be connected to this unit
if it is Ai-NET compatible. With a CD Changer connected to the Ai-
NET input of this unit, the CD Changer will be controllable from this
unit.
Using the KCA-400C (Multi-Changer Switching device) or the
KCA-410C (Versatile Link Terminal) multiple changers can be
controlled by this unit.
See “Multi-Changer Selection (Optional) ” on page 32 for selecting the
CD Changers.
• The controls on this unit for CD Changer operation are operative
only when a CD Changer is connected.
• The DVD changer (optional) is controllable from this unit as well as
the CD changer.
1
Press SOURCE/ to activate the CHANGER mode.
The display shows the disc number and track number.
• The source indicator varies depending on the connected source.
• Press BAND/TA to switch the Disc mode in the Changer mode.
2
Press FUNC./SETUP to activate the Disc selection
mode.
3
Press the disc select buttons (1 through 6)
corresponding to one of the discs loaded in the CD
Changer.
The selected disc number appears in the display and
CD/MP3 playback starts.
• After selecting the desired disc, you can operate in the same way as
for the CD player of this unit.
For details, please see the CD/MP3/WMA/AAC section.
* When a 12-disc CD changer is connected.
Playing MP3 Files with the CD Changer
(Optional)
If you connect a changer compatible with MP3, you can play CD-
ROMs, CD-Rs, and CD-RWs containing MP3 files on this unit.
1
Press SOURCE/ to switch to the MP3 Changer
mode.
2
Press FUNC./SETUP to activate the disc selection
mode.
M.I.X./REPEAT operation mode Disc selection mode
M.I.X./REPEAT operation mode
3
Press any one of the disc select buttons
(1 through 6) corresponding to one of the discs
loaded in the CD Changer.
4
To pause playback, press //ENT.
Pressing / /ENT again will resume playback.
• The unit can play discs containing both audio data and MP3 data.
• For operating MP3 with an MP3 compatible CD Changer, refer to
“CD/MP3/WMA/AAC” on pages 12 to 15.
Multi-Changer Selection (Optional)
Alpine’s Ai-NET system will support up to 6 CD Changers. When
operating two or more changers, the KCA-400C (Multi-Changer
Switching device) must be used. If you use 1 Switching device, you can
connect up to 4 CD Changers. If you use 2 Switching devices, you can
connect up to 6 CD Changers. When using KCA-410C (Versatile Link
Terminal), you can connect two changers and two external outputs
(AUX).
1
Press SOURCE/ on this unit to activate the CD
Changer mode.
2
Press BAND/TA to activate the CD Changer
Selection mode.
The CD Changer Selection mode remains active for several
seconds.
3
Press BAND/TA until the desired CD Changer
indicator appears on the display.
• If the selected CD Changer is not connected, the display will show
“NO CHANGER (No.)”.
• To operate the selected changer, see “CD/MP3/WMA/AAC”
(pages 12-15).
• For further details about the external input (AUX) when using
KCA-410C, see “Setting the AUX Mode (V-Link)” on page 25.
Changer (Optional)
Select buttons
(1 through 6)
BAND/TA
SOURCE
/
FUNC./SETUP
//ENT
Disc Select Mode
(Disc No.1~6)
Disc Select Mode*
(Disc No.7~12)
RPT/M.I.X. Mode
Disc Select Mode
(Disc No.1~6)
01GB00CDA-9887R.book Page 32 Thursday, March 15, 2007 3:55 PM
To Next Page
Loading...
