58-EN
To prevent external noise from entering the audio system.
• Locate the unit and route the leads at least 10
cm away from the car harness.
• Keep the battery power leads as far away from other leads as possible.
• Connect the ground lead securely to a bare metal spot (remove any paint, dirt or grease if necessary) of the car chassis.
• If you add an optional noise suppressor, connect it as far away from the unit as possible. Your Alpine dealer carries various noise
suppressors, contact them for further information.
• Your Alpine dealer knows best about noise prevention measures so consult your dealer for further information.
1 Antenna Receptacle
2 Audio Interrupt In Lead (Pink/Black)
Connect this lead to the Audio Interface output of a cellular
phone which provides ground shorting when a call is
received.
3 Remote Turn-On Lead (Blue/White)
Connect this lead to the remote turn-on lead of your
amplifier or signal processor.
4 Dimmer Lead (Orange)
This lead may be connected to the vehicle’s instrument
cluster illumination lead. This will enable the vehicle’s
dimmer control to dim the backlighting of the unit.
5 Switched Power Lead (Ignition) (Red)
Connect this lead to an open terminal on the vehicle’s fuse
box or another unused power source which provides (+) 12V
only when the ignition is turned on or in the accessory
position.
6 Ground Lead (Black)
Connect this lead to a good chassis ground on the vehicle.
Make sure the connection is made to bare metal and is
securely fastened using the sheet metal screw provided.
7 Power Antenna Lead (Blue)
Connect this lead to the +B terminal of your power antenna,
if applicable.
• This lead should be used only for controlling the vehicle's
power antenna. Do not use this lead to turn on an amplifier or
a signal processor, etc.
8 Battery Lead (Yellow)
Connect this lead to the positive (+) post of the vehicle’s
battery.
9 ISO Power Supply Connector
! ISO Connector (Speaker Output)
" Left Rear (+) Speaker Output Lead (Green)
# Left Rear (–) Speaker Output Lead (Green/Black)
$ Left Front (+) Speaker Output Lead (White)
% Left Front (–) Speaker Output Lead (White/Black)
& Right Front (–) Speaker Output Lead (Grey/Black)
( Right Front (+) Speaker Output Lead (Grey)
) Right Rear (–) Speaker Output Lead (Violet/Black)
~ Right Rear (+) Speaker Output Lead (Violet)
+ Remote Control Input Lead (White/Brown)
Connect the external Alpine product to the remote control
output lead.
, Monitor Control Lead (White/Pink)
Connect this to the Monitor Control Lead of the touch panel-
compatible monitor.
- Video Output Connector
This connector is used in combination with the video inputs
of another video product (Touch panel compatible monitor,
etc.)
. External Junction Box Connector
Connect to the external junction Box (included)
/ External Junction Box
Use when connecting optical digital cable or the remote
control interface box.
Connect to the external junction box connector.
• Do not install the external junction box at a location subjected
to water such as under the floor mat or air conditioner. This
may cause a malfunction.
•
Do not bundle the external junction box cable with other audio cables.
Doing so may induce noise into your system.
• Keep the external junction box away from the Antenna cables
and the rear side of the unit, otherwise noise may be generated
when receiving radio broadcast.
: Digital Output Terminal (Optical)
Use when combining optical digital input compatible
products.
; Steering Remote Control Interface Connector
To steering remote control interface box.
• Use a steering remote control extension cable (included) if
necessary.
< Vehicle Display Interface Connector
Vehicle Display Interface control signals.
Connect this to the optional Vehicle Display Interface box.
• For details about connections, consult your nearest ALPINE
dealer.
= Ai-NET Connector
Connect this to the output or input connector of other product (CD
changer, Equalizer, iPod adapter*,
etc.) equipped with Ai-NET.
* When connecting iPod, the adapter KCA-420i is required. For
details about connections, refer to the manual of KCA-420i.
> Fuse Holder (10A)
? Rear Output RCA Connectors
RED is right and WHITE is left.
@ Front Output RCA Connectors
RED is right and WHITE is left.
[ Subwoofer Output RCA Connectors
RED is right and WHITE is left.
\ Power Supply Connector
] System Switch
When connecting a processor using Ai-NET, place this
switch in the EQ/DIV position. When no device is
connected, leave the switch in the NORM position.
• Be sure to turn the power off to the unit before changing the
switch position.
^ Ai-NET Cable (Included with CD Changer)
_ RCA Extension Cable (sold separately)
{ ISO/JASO Antenna Adapter (sold separately)
ISO/JASO Antenna Adaptor may be required, depending on
the vehicle.
To Next Page
Loading...
