Alpine IDA-X300 - Sound Settings - Core Adjustments; Audio Level and Subwoofer Configuration; Bass, Treble, and Filter Adjustments

19-EN
iDA-X200
iDA-X300
Adjusting Subwoofer/Bass/Treble/
Balance (Between Left and Right)/Fader
(Between Front and Rear)/Loudness/
Defeat
1 Press IMPRINT (iDA-X200 only) or SOUND (iDA-
X300 only) repeatedly to choose the desired mode.
Each press changes the mode as follows:
SUBW LV*
1
BASS LV TREBLE LV BALANCE LV
FADER LV*
2
LOUD*
3
DEFEAT VOLUME
SUBW LV*
1
Subwoofer: 0 ~ 15
Bass level: –7 ~ +7
Treble level: –7 ~ +7
Balance: –15 ~ +15
Fader: –15 ~ +15
Loudness : ON/OFF
Defeat : ON/OFF
Volume: 0 ~ 35
• If IMPRINT (iDA-X200 only) or SOUND (iDA-X300 only) is not
pressed within 5 seconds after selecting the Subwoofer, Bass, Treble,
Balance or Fader mode, the unit automatically returns to normal
mode.
• Loudness introduces a special low-and high-frequency emphasis at
low listening levels. This compensates for the ear’s decreased
sensitivity to bass and treble sound. The function is inoperable when
DEFEAT is set to ON.
*
1
When the subwoofer mode is set to OFF, its level cannot be adjusted.
*
2
If you set the 2.2ch (3WAY)/4.2ch (FRONT/REAR/SUBW.) switch of
the IMPRINT audio processor (PXA-H100) to 2.2ch (3WAY), you
cannot adjust the FADER mode. For details, refer to the Owner’s
Manual of PXA-H100.
*
3
When an external audio processor is connected, this setting cannot
be made.
2 Turn the Double Action encoder (iDA-X200 only)
or Rotary encoder (iDA-X300 only) until the
desired sound is obtained in each mode.
• Depending on the connected devices, some functions and display
indications do not work.
Turning Subwoofer ON/OFF
When the subwoofer is on, you can adjust the subwoofer output level
(refer to page 19).
For iDA-X200, the following setting can be made only when the
IMPRINT audio processor (PXA-H100) is not connected.
1 Press and hold IMPRINT (iDA-X200 only) or
SOUND (iDA-X300 only) for at least 2 seconds to
activate the AUDIO selection mode.
2 Turn the Double Action encoder (iDA-X200 only)
or Rotary encoder (iDA-X300 only) to select the
SUBW mode, and then press
/ENTER.
SUBW SUBW SYSTEM* BASS TREBLE HPF
SUBW
* Displayed only when subwoofer is ON.
3 Turn the Double Action encoder (iDA-X200 only)
or Rotary encoder (iDA-X300 only) to select SUBW
ON/OFF, and then press
/ENTER.
ON OFF
4 Press to return to normal mode.
• If no operation is performed for 15 seconds, the unit will return to
normal mode automatically.
• If is pressed during setting, the unit returns to the previous item.
Setting the Subwoofer System
When the subwoofer is on, you can select either SYS 1 or SYS 2 for the
desired subwoofer effect.
For iDA-X200, the following setting can be made only when the
IMPRINT audio processor (PXA-H100) is not connected.
1 Press and hold IMPRINT (iDA-X200 only) or
SOUND (iDA-X300 only) for at least 2 seconds to
activate the AUDIO selection mode.
2 Turn the Double Action encoder (iDA-X200 only)
or Rotary encoder (iDA-X300 only) to select the
SUBW SYSTEM mode, and then press
/ENTER.
SUBW SUBW SYSTEM* BASS TREBLE
HPF SUBW
* Displayed only when subwoofer is ON.
3 Turn the Double Action encoder (iDA-X200 only)
or Rotary encoder (iDA-X300 only) to select the
SUBW SYS 1 or SUBW SYS 2, and then press
/ENTER.
SYS 1 SYS 2
4 Press to return to normal mode.
• If no operation is performed for 15 seconds, the unit will return to
normal mode automatically.
• If is pressed during setting, the unit returns to the previous item.
• This function is inoperable when Subwoofer is set to OFF.
Sound Setting
Double Action encoder
IMPRINT
/ENTER
PRESET
Rotary encoder
SOUND
/ENTER
PRESET