ENGLISH
Introduction:
Please read this OWNER'S MANUAL thoroughly to familiarize yourself with each control and function.
We
at
ALPINE hope that your new PDX-1.600M will give you many years of listening enjoyment.
In
case of problems when installing your PDX-1.600M, please contact your authorized ALPINE dealer.
CAUTION: These
controls
are
for
tuning
your
system.
Please
consult
your
authorized
Dealer
for
adjust-
ment.
LtWARNING
This symbol means important instructions.
Failure
to
heed them can result
in
serious injury or death.
LtCAUTION
This symbol means important instructions.
Failure
to
heed them can result in injury or property damages.
& WARNING
• DO NOT OPERATE ANY FUNCTIONTHATTAKESYOUR ATTENTION AWAY FROM SAFELY DRIVING YOUR
VEHICLE. Any function that requires your prolonged attention should only be performed after coming to a
complete stop. Always stop the vehicle in a safe location before performing these functions. Failure to do so may
result in an accident.
• KEEP THE VOLUME AT A LEVEL WHERE
YOU
CAN STILL HEAR OUTSIDE NOISES WHILE DRIVING.
Excessive volume levels that obscure sounds such as emergency vehicle sirens or road warning signals (train
crossings, etc.) can be dangerous and may result
in
an accident. LISTENING
AT
LOUD VOLUME LEVELS
IN
A
CAR
MAY
ALSO CAUSE HEARING DAMAGE.
• DO NOT DISASSEMBLE OR ALTER. Doing so may result in an accident, fire or electric shock.
• USE THIS PRODUCT FOR MOBILE 12V APPLICATIONS. Use for other than its designed application may
result
in
fire, electric shock or other injury.
• USE THE CORRECT AMPERE RATING WHEN REPLACING FUSES. Failure to do so may result in fire or
electric shock.
• DO NOT
BLOCK
VENTS OR RADIATOR PANELS. Doing so may cause heat to build up inside and may result
in fire.
•
MAKE
THE CORRECT CONNECTIONS. Failure to make the proper connections may result
in
fire or product
damage.
• DO NOT CONNECT A POWER SUPPLY OTHER THAN A DC 12V NEGATIVE GROUND TYPE. Failure to do
so may result in accident or fire.
• BEFORE WIRING, DISCONNECT THE
CABLE
FROM THE NEGATIVE BATTERY TERMINAL. Failure to do
so may result
in
electric shock or injury due to electrical shorts.
• DO NOT
ALLOW
CABLES
TO BECOME ENTANGLED IN SURROUNDING OBJECTS. Arrange wiring and
cables in compliance with the manual to prevent obstructions when driving. Cables or wiring that obstruct or
hang up on places such as the steering wheel, gear lever, brake pedals, etc. can be extremely hazardous.
• DO NOT SPLICE INTO ELECTRICAL
CABLES.
Never cut away cable insulation to supply power to other
equipment. Doing so will exceed the current carrying capacity of the wire and result in fire or electric shock.
•
DO
NOT
DAMAGE
PIPE
OR
WIRING
WHEN
DRILLING
HOLES.
When drilling holes
in
the chassis for installation, take
precautions so as not to contact, damage or obstruct pipes, fuel lines, tanks or electrical wiring. Failure to take
such precautions may result in fire.
• DO NOT USE BOLTS OR NUTS IN THE
BRAKE
OR STEERING SYSTEMS TO
MAKE
GROUND CONNEC-
TIONS. Bolts or nuts used for the brake
or
steering systems (or any other safety-related system), or tanks
should NEVER be used for installations or ground connections. Using such parts could disable control of the
vehicle and cause fire etc.
• KEEP
SMALL
OBJECTS SUCH AS BATTERIES OUT
OFTHE
REACH OF CHILDREN. Swallowing them may
result in serious injury. If swallowed, consult a physician immediately.
& CAUTION
• HALT USE IMMEDIATELY IF A PROBLEM APPEARS. Failure to do so may cause personal injury or damage
to the product. Return it to your authorized Alpine dealer
or
the nearest Alpine Service Center for repairing.
• HAVE THEWIRING AND INSTALLATION DONE BY EXPERTS. The wiring and installation of this unit requires
special technical skill and experience.
To
ensure safety, always contact the dealer where you purchased this
product to have the work done.
• USE SPECIFIED ACCESSORY PARTS AND INSTALL THEM SECURELY. Be sure to use only the specified
accessory parts. Use of other than designated parts may damage this unit internally or may not securely install
the unit in place. This may cause parts to become loose resulting in hazards or product failure.
• ARRANGE THE WIRING SO IT IS NOT CRIMPED OR PINCHED BY A SHARP METAL EDGE. Route the
cables and wiring away from moving parts (like the seat rails) or sharp or pointed edges. This will prevent
crimping and damage to the wiring. If wiring passes through a hole in metal, use a rubber grommet
to
prevent
the wire's insulation from being cut by the metal edge of the hole.
• DO NOT INSTALL
IN
LOCATIONSWITH HIGH MOISTURE OR DUST. Avoid installing the unit in locations with
high incidence of moisture or dust. Moisture or dust that penetrates into this unit may result in product failure.
SERVICE CARE
•
IMPORTANT
NOTICE
This
Amplifier
has
been
type
tested
and
found to
comply
with the limits for a
Class
B computing
device in accordance with the specifications in
Subpart
J
of
Part 15
of
FCC
Rules.
This
equipment
generates and
uses
radio
frequency
energy, and it
must
be installed
and
used properly in
accordance
with
the
manufacturer's instructions.
SERIAL NUMBER:
INSTALLATION
DAT·-:=E:-:
---------
INSTALLATION TECHNICIAN: _
PLACE OF PURCHASE:
•
IMPORTANT
Please record the serial number of your unit in the
space provided here and keep it as a permanent
record. The serial number plate
is
located on the rear
of the unit.
To Next Page
Loading...
