EasyManuals Logo

Alto PRO X-TRA User Manual

Alto PRO X-TRA
11 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #5 background imageLoading...
Page #5 background image
5
Operating Instructions EN
2.4 Operation
1. Always hold the spray lance fi rmly with
both hands! The spray lance is affected
by a lon gi tu di nal thrust of up to 26.5 Nm
when the high pressure washer is operated.
2. Point the nozzle at the ground.
3. Activate the trigger of the spray handle (6a).
4. Always adjust the distance and thus the pres-
sure of the nozzle to the sur face which is to be
cleaned. NOTE: The pressure can be reg u lat ed
on the TORNADO
®
nozzle.
NOTE: Do not cover the machine during operation. If
the machine is left or not used for 5 minutes, it must
be switched off on the start/stop switch (pos. O).
Operation with detergents
Application of detergents is NOT possible if an
extension hose is applied.
1. Fill the tank with a detergent.
2. Mount the TORNADO
®
nozzle and adjust it to low
pressure (turn to the right).
3. Adjust the dosing regulator to the re quired vol-
ume of detergent.
4. Apply the detergent from below and up wards.
5. Let the detergent act for the time stated on the
packing of the detergent and fl ush with pure water.
2.5 Suction mode
The machine can take in water from a rain water
butt as an example. The water inlet hose must not
be too long, approx. 5 m.
1. Make sure that the water butt is not placed on a
lower level than the ma chine.
2. Attach the water inlet hose to the ma chine and
place the other end of it in the water butt.
3. Start the machine.
4. Detach the spray lance and activate the trigger of
the spray lance. Keep the trig ger activated until
water has come out for approx. 15 sec onds.
5. Remount the spray lance and the ma chine is
ready for operation.
NOTE: The internal fi lter of the machine is not
intended for the fi ltration of large quan ti ties of im-
purities. If the water contains leaves, sand or the
like, an external suction fi lter should be mount ed.
For further in for ma tion, please contact your near est
ALTO dis trib u tor.
2.6 End of operation
1. Stop the machine by turning the start/stop switch
(2) to pos. O.
2. Disconnect the plug from the sock et.
3. Shut off the water supply and ac ti vate the trigger
(6a) to relieve the machine of pres sure.
Concerning storage, please refer to section 5.0.
3.0 Accessories EN
Equipment
Only use original accessories.
Nozzles Attached with the bayonet
coupling system. Stored on
the ma chine.
Tornado
®
(8) Universal adjustable nozzle.
Turn to the left:
high pres sure.
Turn to the right:
low pres sure.
Powerspeed
®
(9) Nozzle with rotating jet for
stubborn dirt on hard sur-
fac es.
Extension hose 7 m extension hose in-
creas ing the working range.
Brushes For cars and
other surfaces.
Available in more
shapes.
Tube cleaner 15 m long tube clean er for
the clean ing of tubes and
drains.
Water-sand- For removal of paint and rust.
blasting equipment Sand avail a ble from do-it-
yourself shops.
Patio Clean er Equipment for quick
and regular clean ing
of horizontal (tiles
etc.) and vertical
sur fac es.
Garden brush Rotating brush for cleaning of
wooden surfaces.
Rim brush Rotating brush for cleaning of
wheel rims.
Detergents
Only use original accessories.
Stone & Wood For fl agstones, brick- and
Cleaner woodwork.
Suitable for moss and algae.
Plastic Cleaner For plastic and syn thet ic
ma te ri als such as garden
fur ni ture.

Other manuals for Alto PRO X-TRA

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Alto PRO X-TRA and is the answer not in the manual?

Alto PRO X-TRA Specifications

General IconGeneral
BrandAlto
ModelPRO X-TRA
CategoryPressure Washer
LanguageEnglish

Related product manuals