Amba RADIANT RSWH-P - User Manual

RADIANT SQUARE
INSTALLATION INSTRUCTIONS
Please read the following information before installing and using your Heated Towel Rack.
WARNINGS
- These units should be installed by a certified electrician in accordance with the National Electrical Code (NEC) and the Canadian Electrical Code (CEC).
- The unit requires a 120 volt, 60Hz power source and should be installed on a GFCI protected circuit.
- Plug-in units should be connected to a grounded outlet with a minimum rating of 10 amps.
- Follow installation instructions to ensure unit is securely fixed to wall. Unit is designed for drying towels. Under no circumstances should anybody climb on or hang on unit.
- Unit is intended for indoor use only. Do not place units inside a shower, sauna, steam room, or wherever unit would be exposed to water.
CAUTION
- As this is a heating device, the surface temperature can increase depending on the ambient temperature in the room and the number of towels applied to the unit.
- Overloading the unit will cause the unit to become extremely hot and may result in a burn if touched and/or damage to towels.
- The fasteners provided with the installation kit are for convenience only and are not suitable for all installation conditions.
- It is the ultimate responsibility of the installer to ensure suitable mounting hardware is used.
OPERATING INSTRUCTION
- After installation, connect the electric power.
- Remove the protective cover from the switch and turn it to the on position.
- The indicator light will glow red and the towel warmer will start to heat — Allow 10-20 minutes to heat up.
- This towel warmer has been designed to run continuously — Turn off the switch or unplug the cord when the towel warmer is not in use for long periods of time.
- Never use an extension cord for Plug-in models.
- The Radiant Collection features an
Integrated on/off switch.
- Remove plastic cover after installation.
- Switch is located on the bottom of the
right vertical bar.
- Press switch to power on unit.
- Switch will illuminate when on.
CARE & MAINTENANCE
- Towels which contain soap or detergent residue may appear to have scorch marks; this is simply discoloration of the residue in the towels themselves.
- The unit is constructed from extremely durable 304 stainless steel. To maintain a good appearance, follow these simple instructions:
- For routine cleaning, simply switch off the unit, allow to cool to room temperature, wipe with a damp cloth and buff with a soft, dry cloth.
- Under no circumstances should abrasive cleaners be used to clean the unit.
CONTACT
TEL:
404‐3509738
FAX:
404‐3550166
EMAIL:
customerservice@ambaproducts.com
WEB:
www.ambaproducts.com
INCLUDED COMPONENTS
4x
DB
4x
G
1x
2x
I
H
1x
4x
E
M8x28
A
4x
C
4x
4x
F
M
ST4.2x40
5x6
PLUG-IN MODELS INTEGRATED SWITCH
REQUIRES
GROUNDED
OUTLET
AVAILABLE MODELS
RSWH-P
RSWP-P
RSWH-B
RSWP-B
WH - wall mounted & hardwired
WP - wall mounted & plug-in
Page 1
SWITCH
SWITCH
COVER
P-Polished B-Brushed
! CAUTION — SURFACE OF UNIT IS HOT WHEN ON !
TOOLS REQUIRED
ELECTRICAL INFO
Two year limited warranty
with proof of purchase will
apply if all Terms and
Conditions of Sale are met
and Installation Instructions
are adhered to.
WARRANTY
www.ambaproducts.com/warranty
FOR FULL WARRANTY VISIT:
150
watts
1.3
amps
120
volts

Summary

Safety Warnings

Cautions During Use

Operating Instructions

Initial Operation Steps

Connect electric power, turn the switch on, and wait for the indicator light.

Continuous Use and Shut-off

The unit runs continuously; turn off or unplug when not in use for extended periods.

Care and Maintenance

Cleaning Procedures

Wipe with a damp cloth, buff dry, and avoid using abrasive cleaners for routine cleaning.

Understanding Discoloration

Scorch marks are caused by soap or detergent residue in towels, not unit damage.

Product Warranty Information

Electrical Specifications

Available Models

Contact Information

Assembly Steps

Attaching Brackets

Step 1: Attach brackets using screws and wall anchors as shown in the diagram.

Mounting the Unit

Step 2: Mount the towel rack onto the attached brackets, securing with screws.

Final Securing

Step 3: Secure the unit using provided fasteners, avoiding over-tightening set screws.

Powering On

Step 4: Turn the unit on using the integrated switch.

Overview

1. Function Description
2. Important Technical Specifications
3. Usage Features
4. Maintenance Features
5. Warranty

The Amba Radiant Square is a heated towel rack designed for drying towels indoors. It is available in both wall-mounted and plug-in models, with options for polished or brushed finishes.

Function Description:

The primary function of the Amba Radiant Square is to warm and dry towels. It operates continuously once turned on, providing a warm surface for towels. The unit is designed to be installed by a certified electrician and connected to a 120-volt, 60Hz power source on a GFCI-protected circuit. Plug-in units require a grounded outlet with a minimum rating of 10 amps.

Important Technical Specifications:

• Power Source: 120 volts, 60Hz.
• Circuit Requirement: GFCI protected circuit.
• Plug-in Outlet Rating: Minimum 10 amps.
• Power Consumption: 150 watts.
• Current: 1.3 amps.
• Material: Extremely durable 304 stainless steel.
• Dimensions (approximate):
  • Width: 22 7/16 inches (570mm)
  • Height: 18 7/8 inches (480mm)
• Models Available:
  • RSWH-P: Wall-mounted & hardwired, Polished
  • RSWH-B: Wall-mounted & hardwired, Brushed
  • RSWP-P: Wall-mounted & plug-in, Polished
  • RSWP-B: Wall-mounted & plug-in, Brushed

Usage Features:

• Installation: Requires installation by a certified electrician in accordance with the National Electrical Code (NEC) and the Canadian Electrical Code (CEC). The unit must be securely fixed to the wall using appropriate mounting hardware; the fasteners provided are for convenience only and may not be suitable for all installation conditions.
• Operation:
  1. After installation, connect the electric power.
  2. Remove the protective cover from the integrated on/off switch.
  3. Turn the switch to the "on" position. The indicator light will glow red, and the towel warmer will begin to heat.
  4. Allow 10-20 minutes for the unit to heat up to its operating temperature.
  5. The unit is designed to run continuously. To turn it off, either flip the switch or unplug the cord (for plug-in models) when not in use for long periods.
• Safety Precautions:
  • Do not climb or hang on the unit.
  • Intended for indoor use only; do not place in showers, saunas, steam rooms, or areas exposed to water.
  • Surface temperature can increase based on ambient room temperature and the number of towels applied.
  • Overloading the unit can cause it to become extremely hot, potentially leading to burns or damage to towels.
  • Never use an extension cord with plug-in models.
  • The surface of the unit is hot when on.

Maintenance Features:

• Cleaning:
  1. Switch off the unit.
  2. Allow the unit to cool to room temperature.
  3. Wipe with a damp cloth.
  4. Buff with a soft, dry cloth.
  5. Do not use abrasive cleaners.
• Discoloration: Towels containing soap or detergent residue may appear to have scorch marks; this is simply discoloration of the residue on the towels themselves, not damage to the unit.

Warranty:

A two-year limited warranty is provided with proof of purchase, applicable if all Terms and Conditions of Sale are met and Installation Instructions are adhered to. For full warranty details, visit www.ambaproducts.com/warranty.

Amba RADIANT RSWH-P Specifications

General

Brand	Amba
Model	RADIANT RSWH-P
Category	Food Warmer
Language	English